Clary Corporation S1500-601 소유자 사용 설명서 - 페이지 10

{카테고리_이름} Clary Corporation S1500-601에 대한 소유자 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Clary Corporation S1500-601 17 페이지. S series continuous power system

페이지 인쇄

SUMMARY OF INDICATORS AND CONTROLS

SYSTEM POWER SWITCH - The main control

switch that engages utility power to the entire unit.

By activating this switch it initializes normal

operation.

AC In - The utility input indicator that identifies

status of the line voltage. If the line voltage is within

the specified range, it will remain lit. If the AC input

is out of range, this indicator will flash in 1 to 2

second intervals.

Inverter - This indicator identifies the status of the

regenerated, conditioned protected output power.

This indicator will stay ON as long as protected

power is available from the power inverter generator.

Battery Level - This is the battery status bar graph.

During normal operation, this bar graph will show the

charging of the battery; all indicators lit will represent

a fully charged battery. During battery operation,

this bar graph represents a discharge meter

indicating less battery time available as each light

goes OFF.

Load Level - This is the system output capacity

status bar. The number of lights on the graph

indicate an approximate percentage of system full

load. All lights being ON would indicate full load.

Cold Start - A momentary push-button switch to

activate the system in the event no utility power is

available. The system will be allowed to start up by

using power from its internal battery. Depress this

switch, the indicator above it will light, and hold it in

until the audible alarm beeps once. The system will

maintain a load depending upon the condition of the

battery.

Load I - A momentary push-button switch that

toggles the output LOAD I AC output terminals at the

rear panel. Unless the unit is powered up using the

Cold Start switch, the output load will normally be

connected to the inverter generator output. The

indicator above the switch will be ON to represent

this. Depressing the switch can disconnect the

output. While the switch is depressed, the indicator

will blink to represent transition. Once the indicator

stops blinking, the switch can be released for a

successful transition.

Load II - A momentary push-button switch that

works identical to LOAD I except it corresponds to

the LOAD II AC output terminals at the rear panel.

SNMP – (Optional) A slot available to install an

interface card to provide system network

management.

T H E C O N T I N U O U S P O W E R C O M P A N Y

Alarm Silent/Test - A momentary push-button

switch that controls two different functions

depending on the mode of operation. In the normal

mode of operation, if this switch is depressed and

held in, the above indicator will blink. Once it stops

blinking, the unit will perform an internal 1 to 2

minute battery check. Once the test is completed, if

the battery is below standards, the system will

indicate that the battery needs replacing. The

system will not run this battery test unless the

battery is detected to be fully charged. During

battery or abnormal operation, an audible alarm will

accompany this mode. By depressing this switch,

the adjacent indicator will blink. When it stops

blinking, the alarm will be silenced. Once the fault or

reason for the alarm is corrected, this audible alarm

condition will automatically reset. The audible alarm

can be re-enabled during abnormal conditions by

pressing and holding the switch again.

NOTE - All switches must be held in for at least two

seconds to engage their function. This is to prevent

any inadvertent switch operation.

Alarm - This is a fault indicator that will light in the

event that the inverter generator is non-operable.

This could be due to an over temperature situation

or an inverter malfunction.

INPUT – An input cord with L5-20P(120Vin) or

L6-15P(240Vin) to an IEC320(UPS).

FUSE – The power protection device for the input

circuitry.

DC INPUT - The auxiliary battery input connector to

add optional batteries for extended backup time.

120VAC OUTPUT (Load I & Load II) - The output

receptacle that can be independently controlled by

the corresponding front panel switch. During normal

operation, inverter generator power is supplied at

these outlets. Three separate hardwire circuits have

been provided. They are individually protected by

circuit breakers.

SIGNAL - A DB-9 subminiature, female connector

that outputs the open-collector signal contacts that

generate a low state during utility interrupt, low

battery and inverter off conditions.

RS232 - A DB-9 subminiature, female connector that

outputs true RS232 computer communications

signals.

IDENTIFICATION LABEL - The model number and

serial number of the system is located here. This

label is located on the underside of the unit Always

refer to this information when corresponding with the

factory.

Page 10