CTS MCT-5002SFP+ 사용자 설명서 - 페이지 2
{카테고리_이름} CTS MCT-5002SFP+에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. CTS MCT-5002SFP+ 2 페이지. 100m/1g/2.5g/5g/10g nbase-t to 10gbase-r standalone media converter
페이지 인쇄
5. DIP SWITCH Setting
The default setting for PIN 1 through PIN 4 is OFF,
ON.
Pin NO.
Function
OFF
Fiber Auto-
1
Disable
Negotiation
2
Link Alarm
Disable
Fiber Loopback
3
Disable
Mode
4
TP Port Speed
Auto-Speed
Configure
via software
Software
of CTS
5
Control
MCT-RACK
-MGM
chassis
6
Reserved
N/A
NOTE:
1.
Before adjusting the configuration of the Dip Switch, the
power should be unplugged.
2.
PIN1, PIN 2, PIN 3 and PIN 4 work only when PIN 5 is set
to ON.
3.
When the fiber loopback mode is enabled (PIN 3 is set to
ON), the media converter will loopback the received
packets (The packets are generated from the 3rd-party
device) to ensure the circuit quality, and TP port will be
forcibly stopped transmitting and receiving the packets.
6. Installing MCT-5002SFP+ on
MCT-RACK Chassis Series
Up to 6 sets of MCT-5002SFP+ installation can be supported
by CTS MCT-RACK-12/18 chassis series. For more details on
these installation, you may refer to our MCT-RACK-12/
18-MGM chassis HW User's Guide.
For proper heat dissipation for MCT-RACK-18 chassis series,
please avoid using slot 1 as well as slot 18, and not to install
any modules next to the slot in which MCT-5002SFP+ is
installed to keep adequate ventilation.(See Fig. 3). As to MCT-
RACK-12 chassis series, the staggered installation for your
MCT-5002SFP+ is highly recommended. (See Fig.4).
Fig 3. MCT-5002SFP+ Installation on
MCT-RACK-18 Chassis Series
and PIN5 is
Fig 4. MCT-5002SFP+ Installation on
ON
Enable
7. Transmission Distance Using
Enable
Copper Cables
Enable
Fixed in
10Gbps
Configure
via DIP
Switch
*Please refer to the NBase-T specifications.
N/A
8. Technical Specifications
Standards:
Interfaces:
LEDs:
Power:
Power
Consumption:
Weight:
Dimensions:
Temperature:
Humidity:
Certification:
Media:
*Please contact us for further reports and updates.
NOTE: Specifications may change without prior notice.
Contact Information
Connection Technology Systems INC (CTS)
18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221, TAIWAN, R.O.C.
TEL: +886 2 26989661 FAX: +886 2 26989662
E-Mail: [email protected]
MCT-RACK-12 Chassis Series
802.3u, 802.3ab, 802.3z, 802.3bz,
802.3ae, and 802.3an
1 x NBase-T (100M/1G/2.5G/5G/10G)
RJ-45 connector
1 X F/O port (SFP+)
Power, Status, FDX, Link/ACT of F/O, and
Link/ACT of TP
I/P
AC 100-240V, 50/60Hz
O/P DC 12V/1.5A
8W
0.13Kg
51mm(W)X74mm(D)X20mm(H)
o
o
Operating: 0
~50
C
o
o
Storage: -20
~60
C
5%~90% RH
FCC/CE Class A
TP
EIA/TIA-568 CAT 5e, 1000M
Fiber
50/125um multi-mode fiber
9/125, 10/125um single-mode
fiber
MCT-5002SFP+
100M/1G/2.5G/5G/10G
NBASE-T to 10GBASE-R
Standalone Media Converter
User's Guide
Version 1.0