Lenovo ThinkServer 사용자 설명서 - 페이지 32

{카테고리_이름} Lenovo ThinkServer에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Lenovo ThinkServer 46 페이지. Machine type: 0387, 0388, 0389, 0390, 0391, 0392, 0393 and 0441
Lenovo ThinkServer에 대해서도 마찬가지입니다: 사양 (8 페이지), 매뉴얼 (36 페이지), 사용자 설명서 (32 페이지), 안전 정보 매뉴얼 (20 페이지), (스페인어) 보증 및 지원 정보 (40 페이지), (프랑스어) 보증 및 지원 정보 (40 페이지), (포르투갈어) 보증 및 지원 정보 (40 페이지), (포르투갈어) 보증 및 지원 정보 (38 페이지), (이탈리아어) 보증 및 지원 정보 (38 페이지), (독일어) 보증 및 지원 정보 (42 페이지), (네덜란드어) 보증 및 지원 정보 (42 페이지), (노르웨이어) 보증 및 지원 정보 (36 페이지), (덴마크어) 보증 및 지원 정보 (36 페이지), (러시아어) 보증 및 지원 정보 (42 페이지), (일본어) 보증 및 지원 정보 (36 페이지), (그리스어) 보증 및 지원 정보 (42 페이지), (폴란드어) 보증 및 지원 정보 (42 페이지), (체코어) 보증 및 지원 정보 (38 페이지), (터키어) 보증 및 지원 정보 (36 페이지), (슬로베니아어) 보증 및 지원 정보 (36 페이지), (헝가리어) 보증 및 지원 정보 (42 페이지), (아랍어) 매뉴얼 (34 페이지), (슬로바키아어) 보증 및 지원 정보 (38 페이지), 보증 및 지원 정보 (34 페이지), 매뉴얼 (30 페이지), 보증 및 지원 정보 (42 페이지), 보증 및 지원 정보 (38 페이지), 보증 및 지원 정보 (38 페이지)

Lenovo ThinkServer 사용자 설명서
Operation Steps: from System Login  Operation Report  Policy Operating Status, as shown in the figure below:

3.7.4 EMERGENCY PLAN

If emergency occurs in equipment room, for example, emergency power-off caused by natural factors like earthquake, or part of power supplies in the
equipment room run into critical problems, you need to store the data on all the problematic devices to a hard disk and shut down the machine properly.
The power is completely provided by UPS during this period, so time is very limited.
After enabling the emergency plan, this plan will have a higher priority than all the energy saving policies that have been applied and can control the
power consumption of all the devices in all device groups within the lowest status that can actually be reached, and prolong the power-on time as long
as possible, thereby ensure the maximum possible amount of devices can be shut down properly to protect important data.
Emergency plan supports the management of all the device groups or the specified device groups for emergencies in varying degrees.
1. Enable the Emergency Plan
The process to enable the emergency plan: Enter the Function  Select a Device Group  Confirm to Enable
Operation Steps: After logging into the system, click the "Enable the Emergency Plan" button at the bottom of the screen in any functional module, and
the following screen will pop up:
After clicking "OK", select the device group that needs to load the emergency plan (all the groups are selected by default), then the message
"Successfully enable the emergency plan" will pop up, indicating the selected device group has been running under the emergency plan.
31