Blacoh SENTRY CIP 설치 및 운영 매뉴얼 - 페이지 6
{카테고리_이름} Blacoh SENTRY CIP에 대한 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Blacoh SENTRY CIP 12 페이지. Sanitary flow through dampener
Blacoh SENTRY CIP에 대해서도 마찬가지입니다: 설치 및 운영 매뉴얼 (12 페이지)
페이지 인쇄Operating temperatures are based on the maximum temperature of the wetted dampener
components only.
Temperature and certain chemicals may reduce the maximum allowable working pressure (MAWP)
of the dampener.
Elastomer
Temperature Limits
Materials
Aflas
0°F to +400°F
Buna
+10°F to +180°F
FDA Buna
+10°F to +180°F
EPDM
-60°F to +280°F
Hypalon
-20°F to +275°F
Neoprene
0°F to +200°F
PTFE
+40°F to +220°F
Santoprene
-20°F to +225°F
FDA Silicone
-20°F to +300°F
Viton
-10°F to +350°F
C A U T I O N ! Plastic materials lose strength as temperature increases which reduces the maximum
pressure sustainable by the material.
Non-Metallic
Temperature Limits
Body Materials
PVC
See chart below.
CPVC
+32°F to +180°F
Acetal*
+32°F to +175°F
Noryl
+32°F to +220°F
Polypropylene*
+32°F to +175°F
PTFE
+40°F to +220°F
PVDF
+10°F to +200°F
* Conductive Acetal and Conductive Polypropylene available.
C A U T I O N ! PVC loses strength more rapidly than other plastic materials as temperature increases.
Certain chemicals can also affect material strength reducing maximum pressure ratings. The chart below
shows reduced maximum pressure ratings based on temperature for PVC only.
general guidelines only; selection of dampener materials must be determined by each individual
application to avoid equipment damage and unsafe operation.
Temperature
73.4°F
(23° C)
Maximum
150 psi
Pressure
(10.3 bar)
5
T
EMPERATURE
Non-wetted dampener components may have a lower temperature limit.
(-18°C to +204°C)
(-12°C to +82°C)
(-12°C to +82°C)
(-51°C to +138°C)
(-29°C to +135°C)
(-18°C to +93°C)
(+4°C to +104°C)
(-29°C to +107°C)
(-29°C to +149°C)
(-23°C to +177°C)
(0°C to +82°C)
(0°C to +79°C)
(0°C to +104°C)
(0°C to +79°C)
(+4°C to +104°C)
(-12°C to +93°C)
PVC Maximum Pressure Guidelines by Temperature
80°F
90°F
(27°C)
(32°C)
142.5 psi
135 psi
(9.8 bar)
(9.3 bar)
BLACOH F
LUID
L
IMITS
Applications
High temperature, petroleum based chemicals, strong acids and
bases.
Good flex life; use with petroleum, solvents and oil-based fluids.
FDA-approved food grade; similar characteristics of regular Buna.
Use in extreme cold; good chemical resistance with ketones,
caustics.
Excellent
abrasion
resistance;
applications.
Good abrasion resistance and flex; use with moderate chemicals.
Bellows design; excellent flex life; use with highly aggressive
fluids.
Excellent choice as a low cost alternative for PTFE in many
applications.
FDA-approved food grade material; for use in food and
pharmaceutical processing.
Use in hot and aggressive fluids; good with aromatics, solvents,
acids and oils.
Applications
Good general chemical resistance; looses strength quickly as
temperature rises.
Chlorinated PVC (CPVC) retains strength to higher temperatures.
Good flex life; low moisture sensitivity; high resistance to solvents
and chemicals.
Good resistance to acids and bases; good temperature stability.
Good general purpose plastic; broad chemical compatibility at
medium temperatures.
Use with highly aggressive fluids.
Excellent resistance to most acids and bases; highest temperature
plastic available.
100°F
110°F
(38°C)
(43°C)
112.5 psi
97.5 psi
(7.6 bar)
(6.7 bar)
C
, I
.
ONTROL
NC
good
in
aggressive
acid
Note that these are
120°F
130°F
(48°C)
(54°C)
90 psi
75 psi
(6.2 bar)
(5.2 bar)