Disc Makers ReflexPro7 사용자 설명서 - 페이지 11

{카테고리_이름} Disc Makers ReflexPro7에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Disc Makers ReflexPro7 15 페이지. Cd-r disc duplicator reflexpro series
Disc Makers ReflexPro7에 대해서도 마찬가지입니다: 사용 설명서 (13 페이지), 빠른 시작 매뉴얼 (2 페이지)

페이지 인쇄

1. Press the down arrow until you see "9. Image" then press the 'ENT' button

you should see "9-01. Image P: A Load" Press the down arrow to display "9-

02. Image P: A Delete Image"

2. Press the 'ENT' button and "Delete Image in Partition A?Yes" will display in

the LCD window. Pressing the 'ENT' button will delete the image in the A par-

tition. The message will show "Partition : A Image is deleted" Press the 'ESC'

key to return to the Image submenu.

9.03 Image Info: use this sub-function to show the number of sessions and

tracks on the currently selected partition of the hard drive.

1. Press the down arrow until you see "9. Image" then press the 'ENT' button

you should see "9-01. Image P: A Load" Press the down arrow to display "9-

03. Image P: A Image info"

2. Press the 'ENT' key and the number of sessions and tracks will be displayed,

pressing the up and down arrow will display total time of the image, total MB

of the image, and the tracks and the track size. Note: data tracks will not dis-

play and time length.

9.04 Compare Image: use this sub-function to compare the image to a CD in

the source recorder for the hard drive.

1. Press the down arrow until you see "9. Image" then press the 'ENT' button,

you should see "9-01. Image P: A Load", press the down arrow to display "9-

04. Image P: A Compare Image".

2. Load the top drive (source recorder for the hard drive) with the disc to be

compared and press the 'ENT' button. When the process is finished the

same screens will be displayed as in the full function (5. Compare) but the

disc will not be ejected.

9.05 Select Image: use this sub-function to select which partition on the hard

drive will be used.

1. Press the down arrow until you see "9. Image" then press the 'ENT' button

you should see "9-01. Image P: A Load", press the down arrow to display "9-

05. Image P: A Select Image".

2. Press the 'ENT' key and the LCD will display "Select Working Partition - A".

1-800-237-6666

Pressing the up and down arrows will cycle through the partitions on

the hard drive. At the desired partition press the 'ENT' key and "Set

Partition to ..." will be displayed to confirm that the partition is selected.

The ReflexPro unit is equipped with an eighty GB hard drive. Each partition is

approximately 1 GB. The partitions are arranged alphabetically, A through Z,

AA through AZ, and BA through BW

9.06 Image Source Drive: use this sub-function to select which recorder is

used as the source reading a CD to the hard drive. The ReflexPro is defaulted to

use the top recorder drive in the unit.

1. Press the down arrow until you see "9. Image" then press the 'ENT' button

you should see "9-01. Image P: A Load", press the down arrow to display "9-

06. Image P: A Image Src Drive".

2. Press the 'ENT' key and the LCD will display "Select Img Src: 01 IDE1 CD-RW

N". Pressing the up and down arrows will cycle through the recorder drive

from 01 at the top to 04 at the bottom, 07 on ReflexPro7. At the desired drive

press the 'ENT' key and "Load image from Drive ID - 0..." will be displayed to

confirm the change in source recorder.

10. E

DIT

RACK

The ReflexPro can be used to create custom audio CDs. This function allows the

user to take audio tracks from different CDs and compile them to a single CD.

This function is only available in the disc to disc mode.

1. Set the ReflexPro to disc to disc mode (see page 9), then select the "Edit

Track" function using the up and down arrows.

2. Load the top drive (Src) with the master disc. Press the "ENT" button once to

see the main screen for this function, "10-01 Edit Track CD to CD Edit." Press

the ENT button again to see the following screen:

www.discmakers.com

Select Track:

1/31

2:41