Armytek Optoelectronics Prime A2 Pro 사용자 설명서 - 페이지 2

{카테고리_이름} Armytek Optoelectronics Prime A2 Pro에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Armytek Optoelectronics Prime A2 Pro 2 페이지. Armytek prime pro flashlights user manual

Set description
Prime
Depending on the model, your flashlight can inconsiderably differ from the pictures in the manual.
ь
The producer reserves the right to change the package at his own discretion without modifying this manual.
ь
Initial Service
1.
2.
The removable magnet in the tailcap.
With its help you can easily attach the flashlight to an electric service panel, a bike handlebar,
above a car wheel, etc.
The magnet can be taken out of the tailcap. To do this unscrew the small cover at the end of the
tailcap and put the magnet out.
Specifying the battery type for correct voltage indication.
Do not specify the type of power source manually unless you use unprotected Li-Ion batteries different from those that are stated by
default: 1xAA (for A1 Pro) / 2xAA (for A2 Pro) / 1xCR123A (for C1 Pro) / 1x18650 Li-Ion (for C2 Pro).
Press & Hold
Release & Click
OFF
Firefly1
Max
x1
Main3
Firefly2
Main2
Firefly3
(for C2 Pro)
Main1
To access the Menu press and hold the switch button (when the flashlight is switched off). It will switch on, go through the all available
modes and then switch off again. After switching off, release the button quickly and click it rapidly again. The flashlight will enter the Menu
and the LED will flash about 3 times a second.
Now you can specify the battery type:
1 click for 1xAA (A1 Pro) / 1xCR123A (C1 Pro) / 1x18650 Li-Ion.
§
2 clicks for 2xAA (A2 Pro) / 2xCR123A (C2 Pro).
§
3 clicks for 1x14500 Li-Ion (A1 Pro) / 1xRCR123 Li-Ion (C1 Pro) / 2xRCR123 Li-Ion (C2 Pro).
§
After the choice is made the light will flash 1, 2 or 3 times to show the battery type chosen.
We recommend NOT to leave power sources inside the flashlight for a long storage period, as batteries (especially, non-rechargeable) can leak for
various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries in, use new and
quality batteries, store the flashlight in acceptable for batteries operational temperature and revise the batteries' state at least once a month. If you
have noticed any signs of batteries' defects, withdraw them from the flashlight and take out of operation. It is also recommended to replace
discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.
Items included in the package:
Flashlight
Lanyard
§
Holster
2 spare O-rings
§
Magnet
Clip
§
User manual
§
x2
To set/replace batteries:
3.
1. Unscrew the tailcap.
2. Place the batteries with the positive contact
(+) facing the head of the flashlight.
3. Adjust the tailcap and tighten it as far as it can go.
The flashlight is ready for operation.
Click x1, x2 or x3
1xAA /
x1
1xCR123 /
1x18650 Li-Ion
2xAA /
x2
2xCR123A
1x14500 Li-Ion /
x3
1xRCR123 Li-Ion
2xRCR123 Li-Ion
Main
The flashlight has 4 Sections of modes:
Click x2
Press & Hold
[Section1] – Firefly modes
OFF вMain
Main1 вMain2
[Section3] – Maximum
Any mode вMain
е
з
Main3
In OFF state:
Main вFirefly
Click: To turn on the last used mode (Firefly, Main or Maximum). If the
Firefly
Click x2
Press & Hold
flashlight was turned on in one of the Special modes it will turn on in the last
used Main mode.
Main вFirefly
OFF вFirefly
Firefly вMain
Press and hold: To turn on Firefly1 mode in [Section 1].
Firefly1 вFirefly2
In ON state:
е
з
Firefly3 (for C2 Pro)
Click: To turn off the flashlight.
Maximum
Click x3
Press & Hold
Press and hold: To start cycling through the modes of the current Section. In
Maximum mode it starts cycling through the Main modes in [Section 2].
OFF вMax
Main1 вMain2
Any mode вMax
е
з
The same in OFF & ON states:
Main3
2 clicks: To turn on the last used Main mode [Section 2]. Further double clicks
will switch modes between the last used modes in [Section 1] and [Section 2].
Special
Click x4
Press & Hold
3 clicks: To turn on the Maximum mode [Section 3].
OFF вSpecial
Strobe
4 clicks: To turn on the last used Special mode [Section 4].
Any mode вSpecial
гд
Beacon
Only C2 Pro has 2 types of operation:
1. General. The flashlight is switched on/off permanently.
State Indication
Switching State Indication ON/OFF
Battery level
2. Tactical. The light turns on for the time the button is being pressed. It will
+
1
2
switch on in the last memorized mode (except for the Special modes). This
< 100%
< 50%
type of operation is useful for short-time lighting and setting signals.
To access the Tactical operation type, unscrew the tailcap to 1/4, press the
Press & Hold
5sec
button and tighten the tailcap again keeping the button pressed. To return to
Low Battery Indication
High Temperature Indication
the General type, unscrew the tailcap to 1/4 and tighten it again.
Warning
Critical
Warning
Critical
You have a convenient momentary access to all Modes:
Main. Double click from OFF or ON state turns on the last used Main Mode.
Firefly. Press and hold the button in OFF-state to turn on the Firefly1. Press
and hold after Firefly activation to start cycling through the Firefly modes:
1sec
0.5sec
1sec
1sec
release the button to select one. Firefly modes can be also accessed from the
Main mode by a double click.
< 25%
< 5%
WARM
HOT
< 10%
HOT
вFirefly1
вMain3
Maximum. 3 clicks from OFF or ON state turn on the Maximum mode.
вOFF
вFirefly2
Special modes (Strobe / Beacon). 4 clicks from OFF or ON state turn on the last used Special mode: Strobe / Beacon.
Cycling through modes. In ON-state press and hold the button in any mode: the modes of the current Section will start switching
cyclically. Release the button to select the desired mode. In Maximum mode it starts cycling through the Main modes.
Automemorizing. After switching off the last used Mode is memorized for quick 1-click access at next switching on. If the flashlight was
turned on in one of the Special modes it will turn on in the last used Main mode.
Lock-out function. Unscrew the tailcap to 1/4 for the protection from accidental switching on. State indication will be turned off.
Multicolor State Indication. Shows the battery level by short flashes every 5 seconds. C2 Pro has State Indication in OFF state and
Firefly modes, which can be helpful to find the flashlight in the dark. Other models don't have it.
Switching Multicolor State Indication ON/OFF (C2 Pro). It is switched off by default in OFF-state and Firefly modes. To turn on and off:
unscrew the tailcap to 1/4, press the button and holding the button pressed - tighten the tailcap and then unscrew it again. The settings
will be memorized even when battery is changed.
Warning Indication. In ON-state shows the battery level and the temperature inside the flashlight.
Low battery level. When it is <25%, the color LED shows the warning level once a second and the main LED flashes 2 times once a
minute. Critical level <5% is color indicated twice a second and light output decreases to Firefly1 and then switched off.
High temperature. When it increases to the warning level, the color LED flashes 3 times once a second. At critical level the main LED
flashes 4 times once a minute and the light output decreases to Main3 mode. In case the temperature doesn't fall the light output
decreases to Firefly2. At normal temperature the brightness increases to usual level.
Operation
[Section2] – Main modes
[Section4] – Special modes