Blagdon inpond 5 in 1 3000 매뉴얼 - 페이지 16

{카테고리_이름} Blagdon inpond 5 in 1 3000에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Blagdon inpond 5 in 1 3000 18 페이지. Clean pond machine
Blagdon inpond 5 in 1 3000에 대해서도 마찬가지입니다: 매뉴얼 (20 페이지)

페이지 인쇄

TROUBLESHOOTING

Poor Fountain performance

•

Reduced height.

•

Jets blocked.

Clean flow adjusters and fountain

head. Wash under a tap or hose.

Pond Pump Cleaner should be used

to remove lime scale build-up/waste

(see diagram) for improved results.

No flow from pump

1. Check power supply is on.

2. Check fuse and wiring (SEE ELECTRICAL INSTALLATION).

3. Follow low flow procedure as above.

If none of the above works contact Interpet (Blagdon) Consumer Advice Department

(See Faults problem procedure Page 25).

Green water

•

Settlement test the water to ensure that there is no sediment suspended in the water. If

there is, follow the brown cloudy water troubleshooting guide.

•

In order to check that the UVC lamp is operating: Open the filter unit (see page 15)

remove the filter foams and cartridge. Positioned on top of the yellow UVC contact

chamber will be a round viewing window where you should see a faint blue light.

This operation may need to be carried out at dusk as UVC lamps emit a dim blue light

under normal operation. Turning the lamp on and off may aid visual identification.

(Ensure the UVC lamp is not more than 6 months old).

•

The UVC may be working effectively but the filter foam/media is too clean and is

unable to remove the fine coagulated waste. Treat the pond with Clear Pond and do

not clean the foams/media until they are blocked.

•

The filter is too small for the pond, check your filter selection chart.

•

The UVC quartz sleeve is dirty or coated in lime scale. Gently remove the quartz sleeve

and clean.

•

Follow all cloudy water trouble shooting points.

DAISY

To clean, remove head

and rinse.

Or in hard water

areas, use Pond Pump Cleaner

TROUBLESHOOTING & IMPORTANT

UVC light not illuminated

•

Check all fuses / RCD and electrical connections follow electrical installation

Faults - Problem Procedure

Before returning your Inpond to your dealer or contacting our Consumer Advice

Department, please carry out the following steps. This will solve most problems quickly

and easily.

1. Ensure electrical procedures have been followed fully. Check fuses and any cable

connectors/switch boxes.

2. (a) Follow routine maintenance procedure fully. (b) Check location and connecting your

pump details including flow rates. (c) Ensure that your pond volume and pump flow rate

meet the maximum pond size recommended for the filter model on the filter

performance and specification chart. (d) Follow troubleshooting guide.

3. If there is a mechanical breakdown of the filter or UVC, return to the point of purchase

for inspection and advice (You will need proof of purchase).

Guarantee

UV & FILTER

This product is guaranteed against defects in material and workmanship for 3 years from the

date of purchase, under normal usage. The guarantee DOES NOT APPLY in case of improper

use, negligence, lack of maintenace or accidental damage to either the filter or UVC. If the

filter or UVC fails due to a manufacturing fault within this period it will be either repaired or

replaced free of charge. Liability is limited to replacement of the faulty product only; no other

costs will be reimbursed. The guarantee is not transferable and does not affect your statutory

rights. This guarantee does not confer any rights other than those expressly set out above. This

guarantee does not cover the filter foams or UVC bulb, which will need replacing when worn

or every 6 months. If any parts are needed, spares are availible from your retailer.