Arnica Hydra Rain 사용 설명서 - 페이지 11

{카테고리_이름} Arnica Hydra Rain에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Arnica Hydra Rain 20 페이지. Shampoo vacuum cleaner with water filter

페이지 인쇄

Cord Length

: 6 m.

Weight

: 11,5 kg / 7 kg

IV. PREPARING FOR USE

• ATTENTION – Do not insert the mains plug into the wall socket

until the appliance is completely ready for use

• Detach the shampoo hose between shampoo reservoir and

back side of Motor Unit by pulling carefully.

• Lift up the Motor Unit using the handle provided, take the

attachments out of the container.

• When unpacking, please check that all parts are included and

undamaged.

• Keep the accessories for further uses

• Make sure that foam filter is fixed on the float case.

• Put the motor unit back onto the appliance and close the

clamps.

• To connect the hose, insert it into the hose connector.

V. OPERATING THE APPLIANCE

Dry Cleaning:

• Always be sure that the mains plug is removed from the wall socket.

• Make sure that the container, tubes and hose group are dry

and clean.

• Unlock the clamps and lift the motor unit upside down.

• Do not use the appliance without the foam filter.

• Lift up the motor unit

• Remove the water filter body and fill container with clean water

(Max. 2,5 liters - Min. 2 liters). Replace water filter body.

• Put the motor unit back onto appliance and lock the clamps.

• Fit the cleaning accessories most suited to the type of operation

to be performed, on to the suction tubes or directly in to the

handgrip.

• For effective cleaning the following accessory can be used.

» Nozzle (H5) for removing dust from carpets, mats and hard

floor surfaces.

» Crevice nozzle (H2) for cleaning narrow corners and hard to

reach places

» Directly suction tube (E9) for sucking soil, shavings, crumbs, fluff.

» Upholstery Nozzle (H4) and the suction tube for removing

dust from shelves, books, lamp shades, frames, ornaments,

curtains, clothes, electronic equipment's, surfaces.

• Pull the mains cord out of the appliance and insert the mains

plug into the wall socket. Push the On/Off Button (A2) to switch

the appliance on.

ATTENTION : Do not operate the pump during the dry cleaning.

Shampooing & Wet Cleaning:

• Lift the motor unit from the container.

• Make sure that the foam filter is inserted. (Figure 5)

• Remove water filter tube. It may cause extremely bubbling.

• Replace water filter body (Figure 12)

• NEVER FILL THE CONTAINER WITH CLEAN WATER WHILE

PREPARING APPLIANCE FOR SHAMPOOING

• Fill the shampoo resarvoir with clean water (use C4 water level

indicator as reference) and shampoo (dose is mentioned on

shampoo bottle) Place the shampoo reservoir onto the wheel

group (Figure 15)

• Place the container onto the shampoo reservoir and the motor

unit onto the container. Lock the clamps. (Figure 4)

• Insert the short shampoo hose (C3) to the shampoo reservoir

(Figure 16) and to connector on the back side of motor unit.

(Figure 17)

• Attach the long shampoo hose to the shampoo trigger. Other side

of the shampoo hose will be connected to the connector (A3) on

the motor unit.

• Fix the shampoo trigger to the handgrip of the suction hose.

• Attach the long shampoo hose to the suction hose and suction

tubes by means of the clips.

• Attach the shampoo nozzle (F1) to the suction tubes or directly on

to the handgrip. Mini wetsweep can be attached to the handgrip

only. For shampooing the carpets, mats and floor use nozzle, for

shampooing the armchairs, sofas,curtains, car upholstary, etc. use

miniwetsweep. fixing it directly to the handgrip.

• Insert the plug into the wall socket.

• Press the pump switch and operate pump to inject water and

shampoo mix onto the surface to be treated.

• The shampoo and water is injected from the shampoo reservoir

by pump and sprayed through a nozzle on to the surface to be

cleaned. The shampoo penetrates the fibers, dissolving even

the most stubborn dirt. Wait at least three minutes to allow the

shampoo to soak in completely.

• Press the on/off switch which activates the extraction function

and pass over the surface while pump is not operating. For

cleaning the upholstery, sucking up the dirty water, spraying the

shampoo and water mix functions can be made at the same time

operating on/off switch and pump. If bubble starts to come out

of the nozzle, turn off the appliance immediately and empty the

container, check the amount of the shampoo mixed into water.

• Once the container is full with dirty liquid, the float blocks the

suction operation automatically and motor gets noisier. At the

time switch off the vacuum cleaner and pump IMMEDIATELY,

pull out the plug, remove the suction hose (E3) from the hose

connector detach the motor unit and empty the container.

• For cleaning the hard floors like tiles, bricks, marble, ext. fit the

hard floor adapter on to the large wet cleaning head sliding it in

to place from left to right Proceed as described in this section

dealing with spraying and sucking liquids.

• Using the crevice nozzle, you can soak the water discharge from

dish washer or washing machine, spilling of liquids, refrigerators

and freezers defrosting. Attach the crevice nozzle to the handgrip

and switch on for vacuuming liquids.

CAUTION: If you don't use your vacuum cleaner according to the

instructions written above; there is a risk of excess foam occur-

ring and the excess foam might be ejected from the hepa filter.

When you experience a situation like this, you should, turn off

the machine unplug, empty the water tank, clean the water filter

body and dry it. Then, you should also remove the Hepa Filter

and dry it. Wash the foam filter located on the float group and

dry it as well. Wait 1 or 2 hours to dry the foam inside the motor.

VI. CLEANING AND MAINTENANCE

• Always switch the appliance off and remove the mains plug

from the wall socket before starting any maintenance or

cleaning operations.

• Always empty, clean and dry the container after use.

• After wet cleaning, always suck clean water without shampoo

a few minutes for cleaning the accessories, suction tubes and

hose group and than suck air for drying them.

• To ensure perfect hygiene and length the working life of vacuum

cleaner, never leave wet and dirt inside the container.

• Before emptying dirt and waste liquid remove suction hose of

hose group and lift Motor Unit by pulling the clip locks.

• The foam filter can be washed warm, soapy water or running

water. Dry it throughly before planing on to float case. Don't

wash foam filter at washing machine with hot water.

• Clean and check the float valve inside the float case moves

freely in it's housing. For checking the float, lift up the Motor

Unit and shake it.

• Replace the dust bag when it is full of dust

• The cleanness of hepa filter filter should be checked pe-

riodically. Clean the filter if it is not clean. This filter loses

its characteristics after a certain usage period and requires

replacing.

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capa-

bilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use

of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not

play with the appliance.