ARO 613104 운영자 매뉴얼 - 페이지 4

{카테고리_이름} ARO 613104에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ARO 613104 6 페이지. Wash pump detergent pump assembly

LOWER PUMP DISASSEMBLY
NOTE: All threads are right hand.
1. Clamp the lower pump assembly in a vise side ways on the (7) pump
body with the material outlet up.
2. With a plastic hammer tap all around the lower end of the (16) suc-
tion tube. (Close to the bottom).
3. Place strap wrench around the (16) suction tube and hold securely.
Place a wrench on the foot valve body and disassemble from the
suction tube.
4. Remove the (17) dowel pin and (20) ball from the (21) foot valve
body.
5. Remove the (19) "O" ring from (21) foot valve body.
6. Disassemble the (16) suction tube from the pump body.
7. Remove the (3) plunger using extreme caution not to damage the
finish on the O.D.
8. Remove the (9) "O" ring from the (7) pump body.
9. Place the strap wrench on the (2) spacer tube and unscrew the
spacer tube from the (7) pump body.
10. Place a wooden dowel or hammer handle in the (2) spacer tube and
lightly tap the (4) washer, and the (5) packing out of the chamber.
11. Remove the (6) gasket from the (7) pump body.
12. Clamp the flats of the (11) rod in the vise. Remove the (3) plunger
and the (10) lock washer from the (11) rod.
13. Remove the (15) nut.
14. With a spanner wrench remove the (14) retaining nut.
15. Remove the (12) cup and (13) "O" ring.
PAGE 4 OF 6
LOWER PUMP SERVICE PROCEDURES
LOWER PUMP END REASSEMBLY
NOTE: Use anti seizing compound on all stainless steel threads.
1. Thoroughly grease and install the (4) washer, and the (5) packing
into the bore of the (2) spacer tube with the lips toward the opening.
2. Seat the (6) gasket in the (7) pump body.
3. Apply PTFE tape or Parker Ferulube to the threads on the end of the
(2) spacer tube that the packing was installed into, and insert into the
top of the (7) pump body (top does not have external threads) and
screw securely together.
4. Thoroughly grease and install the (9) "O" ring into the bottom of the
pump body.
5. Place the (3) plunger (with 1/2 - 20 thread down) into the top of the
(2) spacer tube, and slowly work the plunger through the (5) pack-
ing, until the plunger extends out of the (7) pump body.
6. Place the (10) lock washer over the threads on the (11) rod.
7. Clean the threads of both pieces with solvent, apply Loctite and
screw securely onto the (3) plunger.
8. Slide the assembled (12) cup and (13) "O" ring onto the (11) rod.
9. Thoroughly clean with solvent and apply Loctite to the 7/16 - 20
threads of the (11) rod.
10. Screw the (14) retaining nut onto the (11) rod and tighten with a
spanner wrench.
11. Screw the (15) nut onto the (11) rod and tighten.
12. Push the assembled (3) plunger and (12) cup up until the cup comes
in contact with the (7) pump body.
13. Thoroughly grease the inside of, and apply PTFE tape or Parker
Ferulube to the external threads of the (16) suction tube. Carefully
force the externally threaded end of the suction tube over the (13)
"O" ring and screw into the (7) body.
14. Thoroughly grease and install the (19) "O" ring on the (21) foot valve
body.
15. Place the (20) ball in the (21) foot valve body and insert the (17) dow-
el pin into the two holes in the foot valve body.
16. Apply PTFE tape or anti-seizing to the threads of the (21) foot valve
body and screw them into the (16) suction tube and tighten securely.
17. The lower pump end is now assembled.
613100-X