DiscreteHeat ThermaSkirt 설치 지침 매뉴얼

{카테고리_이름} DiscreteHeat ThermaSkirt에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DiscreteHeat ThermaSkirt 12 페이지. Discreteheat thermaskirt room heating system

페이지 인쇄

A N

E C O

These instructions are intended as a guide only. Your installation & design may vary - if in doubt ask for help.

If you have any tips or suggestions e-mail them to: [email protected]

Your ThermaSkirt system must be cleansed and protected by a corrosion inhibitor suitable for alluminium

radiators, as required by BS 7593:2006 'Code of Practice for treatment of water in domestic hot central heating

systems'. DiscreteHeat recommends our own TS3 Cleanser and TS5 Inhibitor or Scalemaster CM5 or CM10.

FAILURE TO PROTECT YOUR SYSTEM WILL INVALIDATE YOUR WARRANTY

TOOLS YOU WILL NEED:

A suitable metal cutting saw, preferably a chop saw (only if cutting lengths on site) / A DiscreteHeat rotary de-burring tool / An accurate

quality tape measure (Black & Decker, DeWalt etc.) / String line and chalk or laser level / A Stanley/sharp knife and/or plasterboard saw /

Power drill with hammer action / Power driver / Size 10 screws (50-100mm) / Plastic or timber faced mallet / Rawlplugs and\or plaster-

board fixings / Pipe cutting tool (15mm/16mm) / Various push fit connectors / Your plan and cutting list (if purchased as a room kit).

THE SAME DIMENSIONS AND SPACINGS APPLY TO ANTI-CLOCKWISE INSTALLATIONS.

DO'S AND DON'TS:

Carefully check you have all the parts required by your design systems before you start cutting.

Check all skirting measurements twice before cutting: see diagram on page 2 (unless provided pre-cut).

Ensure that you use the templates (pages 9 - 12) to get your pipes correctly positioned.

DON'T Forget to check the orientation and quantity of retaining clips for each connection and fitting before you insert into skirting - it varies!

DON'T Forget that the FEED and RETURN pipes need to be tight to the wall to ensure your covers fit correctly.

DON'T Forget that aluminium expands (by about 1mm per metre), so make sure the ends of the skirting are not hard up against

any fixed features.

1 .

P O S I T I O N F E E D P I P E S

Remember to allow

for carpet or tiles if

NOT Finished Floor Level

URBAN LT

(6in / 150mm)

100mm

45mm

Tel: 0845 1238367

ThermaSkirt

R E V O L U T I O N

DiscreteHeat Co. Ltd. accept no liability for any errors or omissions.

ALL EXAMPLES SHOWN ARE CLOCKWISE/RH INSTALLATIONS.

CLASSIC TS

(6in / 150mm)

FLOW

15/16mm

100mm

RETURN

15/16mm

45mm

Fax: 01942 665104 e-mail: [email protected] web: www.discreteheat.co.uk

I N S T A L L AT I O N

ISSUE 22 / January 2014 (Download further/latest copies at www.discreteheat.co.uk/technical.html)

I N

R O O M

REGENCY OG

(8in / 200mm)

FLOW

15/16mm

130mm

RETURN

15/16mm

75mm

H E A T I N G

DECO PR/BM

(4.5in / 115mm)

FLOW

15/16mm

RETURN

90mm

15/16mm

35mm

FINISHED FLOOR LEVEL

Page 1

FLOW

15/16mm

RETURN

15/16mm