Distech Controls Allure EC-Smart-Comfort-SF-Dl 설치 매뉴얼 - 페이지 13

{카테고리_이름} Distech Controls Allure EC-Smart-Comfort-SF-Dl에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Distech Controls Allure EC-Smart-Comfort-SF-Dl 13 페이지.

페이지 인쇄

Setting the Allure EC-Smart-Comfort Sensor Subnet ID

Each Allure EC-Smart-Comfort communicating sensor connected to a controller's Subnet Port must be set to a unique subnet ID address. The address is

set through the DIP switch located next to the Subnet Port connectors. Please refer to section

Switch Position

OFF

The Allure EC-Smart-Comfort sensors and Allure EC-Smart-Air sensors share the same addressing range.

Maintenance and Cleaning

Gently clean the device with a soft, lint-free cloth slightly moistened with a solution of mild liquid dish soap and warm water or disinfect the device with a

soft cloth slightly moistened with a 70% isopropyl alcohol.

Do not directly spray any liquid or disinfecting solution on the device. Do not clean with any other chemicals products.

Disposal

The Waste Electrical and Electronic Equipment (WEEE) Directive set out regulations for the recycling and disposal of products. The WEEE2002/96/EG

Directive applies to standalone products, for example, products that can function entirely on their own and are not a part of another system or piece of

equipment.

For this reason Distech Controls products are exempt from the WEEE Directive. Nevertheless, Distech Controls products are marked with the WEEE

symbol

, indicating devices are not to be thrown away in municipal waste.

Products must be disposed of at the end of their useful life according to local regulations and the WEEE Directive.

FCC Statement

Changes or modifications not expressly approved by Distech Controls could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Images are simulated. While all efforts have been made to verify the accuracy of information in this manual, Distech Controls is not responsible for damages or claims arising from the use of this manual.

Persons using this manual are assumed to be trained HVAC specialist / installers and are responsible for using the correct wiring procedures and maintaining safe working conditions with fail-safe environ-

ments. Distech Controls reserves the right to change, delete or add to the information in this manual at any time without notice.

Distech Controls, the Distech Controls logo, Open-to-Wireless, Innovative Solutions for Greener Buildings, and Allure are trademarks of Distech Controls Inc. BACnet is a registered trademark of ASHRAE.

Global Head Office - 4205 place de Java, Brossard, QC, Canada, J4Y 0C4 - EU Head Office - ZAC de Sacuny, 558 avenue Marcel Mérieux, 69530 Brignais, France

13 / 13

OFF

Connectors and DIP Switch Location

4 (EOL)

ON or OFF

See Subnetwork

Bus Topology and

EOL Terminations

EC-Smart-Comfort_IG_15_EN

[pg. 5].

Allure EC-Smart-Comfort

Subnet ID Address