CAMDEN CX-EPD1289L 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} CAMDEN CX-EPD1289L에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. CAMDEN CX-EPD1289L 7 페이지. Electric preload rim strike

페이지 인쇄

2. Secure strike in place with the 1/4-20 x 1-1/4 ( 2 screws).

1. Using center line, measure 4

bottom, and drill

3. Close the door (Ensure crash bar latch does not touch keeper

while closing the door) if necessary, adjust strike so that strike

2. Close door (Ensure crash bar latch does not touch keeper

and crash bar latch are well aligned.

1. Using center line, measure 4

while closing the door) if necessary, adjust strike so that strike

4. While adjusting strike, allow a small gap between strike body

bottom, and drill

Step 2: Aligning the Strike

and crash bar latch are well aligned,

and crash bar (approx.

1. Mark the location and drill the 5/8" diameter hole for the

4. While adjusting strike, allow a small gap between strike body

the remaining 2 middle mounting screw positions on frame.

electrical cable as per template or dimensions shown below.

1. Using center line, measure 4

2. Close door (Ensure crash bar latch does not touch keeper

and crash bar (approx.

2. Secure strike in place with the 1/4-20 x 1-1/4 (2 screws).

bottom, and drill

while closing the door) if necessary, adjust strike so that strike

'' hole for connecting wires, as per drawing.

5. Open the door and remove the strike from the frame, drill and

5. Open door and Remove strike. Drill threads at screws

thread the 2 middle mounting screw holes for the 1/4 - 20 x 1 -

3. Close the door (ensure crash bar latch does not touch keeper

and crash bar latch are well aligned,

position.

1/4 screws.

while closing the door). If necessary, adjust strike so that strike

4. While adjusting strike, allow a small gap between strike body

2. Close door (Ensure crash bar latch does not touch keeper

and crash bar latch are well aligned.

and crash bar (approx.

while closing the door) if necessary, adjust strike so that strike

6. Secure strike with all 1/4 - 20 x 1 - 1/4 screws and fix back the

4. While adjusting strike, allow a small gap between strike

and crash bar latch are well aligned,

5. Open door and Remove strike. Drill threads at screws

latch on the strike. Use the M3 x 6 to secure the strike cover.

body and crash bar (approximately 1/8"). Remove the latch

4. While adjusting strike, allow a small gap between strike body

position.

and crash bar (approx.

5. Open door and Remove strike. Drill threads at screws

position.

Horizontal

Centerline

Horizontal

HORIZONTAL

Centerline

CENTERLINE

Horizontal

Centerline

Top View

Latch

Jamb

Latch

'' top and

'' hole for connecting wires, as per drawing.

''). Remove the latch on strike and mark

'' top and

''). Mark remaining screws position.

Jamb

''). Mark remaining screws position.

Jamb

Horizontal

Centerline

Horizontal

Centerline

Horizontal

Centerline

Top View

Jamb

Top View

Jamb

Allow a small gap between

strike body and crash bar

Allow a small gap between

strike body and crash bar

(Approx. 1/8'')

Crash Bar

'' top and

on strike and mark the remaining 2 middle mounting screw

positions on frame.

5. Open the door and remove the strike from the frame, drill

and thread the 2 middle mounting screw holes for the 1/4 - 20

x 1-1/4 screws.

6. Secure strike with all 1/4 - 20 x 1-1/4 screws and fix back the

Connecting

latch on the strike. Use the M3 x 6 screws to secure the strike

Wire hole

cover.

R+1''

Connecting

R +

Wire Hole

R+1''

Connecting

R+1''

Wire hole

Ø 5 8 ''

R+ 3 4 ''

R+1''

R +

4 3

8 3

4 3

Closed

Closed Door

Door

Ensure latch does not touch

strike keeper while closing door,

and while adjusting strike

Allow a small gap between

Closed

strike body and crash bar.

Door

(Approx. 1/8'')

(Approx.

'')

Allow a small gap between

strike body and crash bar

(Approx. 1/8'')

Crash Bar

Door Jamb

INSTALLATION

6. Connect wires as per drawing.

7. Door Status Sensor(Closed positi

7. Fix strike with remaining screws

White = NO

Orange = COM

(1/4-20 x 1

CX-EPD1289L Electric Preload RIM Strike

Grey = NC

for (2pcs) in the middle

POWER

INSTAL L AT ION INS T RUCT IONS

8. Door Status Sensor(Closed positio

6. Connect wires as per drawing.

White = NO

INSTALLATION INST

7. Fix strike with remaining screws

Orange = COM

(1/4-20 x 1

Grey = NC

for (2pcs) in the middle

6. Connect wires as per drawing.

POWER

8. Door Status Sensor(Closed pos

7. Fix strike with remaining screws

White = NO

(1/4-20 x 1

(4pcs) at both ends / 10-32 x 1

Orange = COM

for (2pcs) in the middle

Grey = NC

8. Door Status Sensor(Closed position)

POWER

White = NO

Orange = COM

Grey = NC

：

POWER

Red/Black,Blue/Green( 12VDC )

Wire hole

Red,Black/Blue,Green( 24VDC )

> Red / Green ( Short Black,Blue

Tighten Set

Screws onto

Fixing Bolts

R +

1/4-20 x 1-1/4

screws x 4pcs

Ensure latch does not touch

Ensure latch does not

strike keeper while closing door,

touch strike keeper while

closing door, and while

and while adjusting strike

adjusting strike.

Ensure latch does not touch

strike keeper while closing door,

and while adjusting strike

Closed

Door

Crash Bar

Door Jamb

INSTALLATION

(4pcs) at both ends / 1

：

Red/Black,Blue/Green

Red,Black/Blue,Green

> Red / Green ( Short

(4pcs) at both ends

：

Red/Black,Blue/Green(

Red,Black/Blue,Green(

> Red / Green ( Short B

：

Red/Black,Blue/Gree

Jamb

Red,Black/Blue,Gree

> Red / Green ( Shor

Jamb

Page 3 of 7