CAMDEN SureWave CM-332 Series 설치 지침 매뉴얼 - 페이지 2
{카테고리_이름} CAMDEN SureWave CM-332 Series에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. CAMDEN SureWave CM-332 Series 8 페이지. Active infrared "hands-free" switches
페이지 인쇄
CM-331 & CM-332 Active Infrared "Hands-Free" Switches Installation Instructions
Wall
Wall Box
Rough Wall
Finish
Recessed
Box
2-Gang (or 4x4) Electrical Box: CM-331W & CM-332W
Diagram 1 - Proper Box Installation
1a – If using an in-wall box ensure the box is plumb and
square, and flush with the wall surface. (See Diagram 1)
1b – If using a surface box, ensure it is secure & plumb.
1c – If using a 4 x 4 box, ensure the box is plumb and
square, and flush with the wall surface, then attach
the metal adaptor plate (included in the CM-331W
& CM-332W packages) to the box using appropriate
fasteners.
2 – Bring your 4-conductor wire through the back or side
of the enclosure and leave approximately 6" tail for
wiring connection.
3 – Make the electrical connections to the device
according to the wiring section (following).
4 – Using the dip switch located on the end of the unit,
set
the operating mode. (See Section 4)
5 – Attach the unit to the enclosure using the two #6-32
screws provided.
6 – Apply power and adjust range and time delay via the
potentiometers on the front of the unit. (See Section
4
for adjustments)
7 – Attach the faceplate to the unit using the two black
#6-32 x 3/8 machine screws or tamperproof screws.
Do not overtighten!!
Door Frame: CM-331W & CM-332W
Smooth
Wall Finish
Flush
Unaligned
Box
1a – If mounting directly in a 1¾" wide aluminum jamb,
make a cutout in the door frame at the intended
location as per Diagram 2 on page 4.
Drill and tap two mounting holes as shown.
1b – If mounting the unit in our CM-23d deep jamb
box, first mount the jamb box according to the
instructions packaged with the enclosure. Using the
CM-23D as a guide, drill a wire access hole through
the jamb to fish the wiring through.
2 – Bring your 4-conductor wire through the back or side
of the enclosure (or Jamb) and leave approximately 6"
tail for wiring connection.
3 – Make the electrical connections to the device
according to the wiring section (following).
4 – Using the dip switch located on the end of the unit, set
the operating mode. (See Section 4)
5 – Attach the unit to the enclosure or jamb using the two
#6-32 screws provided.
6 – Apply power, and adjust range and time delay via the
potentiometers on the front of the unit. (See Section 4
for adjustments)
7 – Attach the faceplate to the unit using the two black
#6-32 x 3/8 machine screws or tamperproof screws.
Do not overtighten!!
Wiring
N
N
C
C
O
TB 3
DIP 3
Relay
1
Request To
1
Exit Input
TB 2
2
Door Contact
3
Input
4
5
External LED
6
Ring Control
TB 1
CM-331
Page 2 of 8
LED Control
DIP Switch
Plugin for
optional
CM-TX-99 RF
module
N
N
N
N
C
C
C
O
C
O
TB 3
TB 4
DIP 3
Relay
Relay
1
2
Request To
1
Exit Input
TB 2
2
Door Contact
3
Input
4
External LED
5
Ring Control
6
TB 1
CM-332
LED Control
DIP Switch
Plugin for
optional
CM-TX-99 RF
module