Acoustic Image Clarus 소유자 매뉴얼 - 페이지 6
{카테고리_이름} Acoustic Image Clarus에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Acoustic Image Clarus 10 페이지. S4plus
Acoustic Image Clarus에 대해서도 마찬가지입니다: 소유자 매뉴얼 (12 페이지)
페이지 인쇄
CH 2
FX
RETURN
FX
RTN
LEVEL
BYP
FX
CH 2
FX
SWITCH
FX
CH 1
FX
SWITCH
BYP
CH 1
FX
RETURN
FX
RTN
LEVEL
Phantom
Off
On
Mic
Channel 2
Atten
Level
Bass
Mid
Treble
Input
Phantom
Off
On
Mic
Channel 1
Atten
Level
Bass
Mid
Treble
Input
Two Channel Control Panel
HEADPHONE
OUTPUT
H/P
AMP
Effects
Send
Phase Inv
Ch 2
Loop
Ambient
60
Delay
Chorus
Plate
Flange
Off On
Room
Hall
30
400
Level
Freq
Off
On
Level
Ch 1
Effects
Low Cut
Return
Effects
Send
Phase Inv
Post EQ
Mute
Loop
60
Off On
30
400
Level
Freq
Master
Off
On
Ch 2
Ground
Low Cut
Return
Direct Out
lift
8
Effects
Our high-quality effects units offer 6 program selections: 3 reverb
programs (Hall, Room and Plate), a delay, an ambient chorus and a
flanger. There are switches to select which of the two channels are
processed by the effects unit. Either channel can be connected to the
effects unit. If both switches are engaged, the selected program
appears in both channels. In the one channel preamp, only one switch
is present. A level control affects the level of the effects signal that is
mixed with the "dry" signal to control the overall effect of the selected
program. You should experiment with both the program selection and
the level control to find the sound that you prefer. When effects are not
used, the switches for both channels should be off and the level
control should be turned fully counterclockwise. Note that the flange
effect is noisy, it is normal the hear the modulation of the flanger when
no signal is present.
Headphone Output
There is headphone output on the rear panel of the amp head. You can
plug a standard 1/4 inch stereo plug into this output to connect a
headphone for private listening. If your headphone has a 1/8th inch
plug, you can buy an adapter to allow you to use the 1/4 inch output
jack.
When you plug into the jack, the amp is muted. Sound will only be
heard through the headphones. The headphone is connected to the
output of the preamp so all of the controls on the preamp, including
effects, will affect the signal heard through the headphone. When the
headphone plug is removed from the jack, the amp will come back on.
There is a short delay between removal of the plug and the amp
coming back on, so expect a pause before you will hear anything
from the amp after the headphone is removed.
plugged into the headphone output jack, the amp will be muted so
make sure that nothing is plugged into the jack when you want to use
the amp normally.
Limiter Switch
Under extreme playing conditions such as high volume or when
driving a low impedance speaker load, the amplifier may be pushed
beyond its limits. When that happens, you will hear high distortion and
you may even cause the overcurrent protection circuit to operate
resulting in an interruption of sound. The power amp is protected
Power
against short circuits in its output. When the amp tries to deliver too
much output current, the overcurrent circuit will operate to prevent
damage. The result is that the power amp is turned off for a second or
two to keep it from delivering too much current. The limiter switch,
located on the rear panel of the amp head, is provided to allow the amp
Anytime anything is
9