Acoustic Research AWS53 설치 및 운영 매뉴얼 - 페이지 2
{카테고리_이름} Acoustic Research AWS53에 대한 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Acoustic Research AWS53 4 페이지. Portable wireless speaker with 3.5mm jack
페이지 인쇄
Tour of the Speaker System
Included Accessories
3.5mm audio in cable
Connecting the Speaker System
Powering the Transmitter
Note:
There is no transmitter ON/OFF switch. The transmitter is designed to be left plugged
in and powered at all times. If you will not be using the
unplug the transmitter AC power adapter.
Connecting to an Audio Source
Connecting to an MP3 player, smartphone, or other portable audio
device
This speaker offers two ways to listen to audio from a portable audio device: using the wireless
transmitter or connecting directly to the audio source.
Using the wireless transmitter
1. Plug the stereo plugs on the provided Y-adapter audio cable
into the AUDIO IN jacks on the back of the transmitter.
2. Plug the mini-plug end of the provided Y-adapter into the
headphone output of your MP3 player or other portable audio
device.
Using a direct connection
1. Connect one end of the provided 3.5mm audio in cable to the
3.5mm
Speaker
AUDIO IN jack on the bottom of the speaker.
audio in cable
(bottom panel)
2. Connect the other end of the cable to the headphone output
on your MP3 player or other portable audio device.
Audio source
Warning:
This product is designed to work with line level outputs or headphone outputs only.
DO NOT
connect it directly to speaker outputs as it will permanently damage the transmitter.
Connecting to an A/V Receiver
3. Connect the stereo plugs on the mini-jack to RCA adapter to the corresponding left and right
audio outputs of your A/V receiver, amp, or other audio source.
Note: These power units should be
plugged in so that they stay vertical
Connect the small, round plug from the transmitter AC
power adapter to the transmitter's DC IN jack. Plug the
other end of the transmitter AC power adapter into any
standard 120V AC wall outlet.
Note:
Be sure to use the AC power adapter rated 12V DC
200 mA (it has the smaller diameter plug).
AWS53
for an extended period of time,
1. Plug the stereo plugs on the provided Y-adapter audio
cable into the AUDIO IN jacks on the back of the
transmitter (make sure to match the colors on the plugs
and jacks).
2. Plug the mini-plug end of the provided Y-adapter into a
mini-jack to RCA adapter (not included).
Connecting the Speaker System
Powering the Speaker
There are two options to power your wireless speaker: using the included AC power adapter or
using 6 AA batteries (not included).
Note:
Be sure to use the speaker AC power adapter rated 9V DC 1200 mA.
Warning:
This product is water-resistant, not waterproof. Avoid prolonged exposure to wet
environments, such as rain, mist, dew, etc. In other words, you can take it out, just don't leave it out.
To avoid electrical shock, use this product with caution near water sources if powered with the
AC adapter. Never submerge in water.
AA Batteries
1. Remove the battery compartment cover on the bottom of the speaker.
2. Insert six (6) AA batteries (not included) into the speaker following the polarity ("+" and "-")
as diagrammed inside the battery compartment.
3. Replace the battery compartment cover on the bottom of the speaker.
Note:
Place the rubber cap in the speaker power input jack when using batteries.
DO NOT
mix batteries with different chemistry types (for example, a zinc battery with an alkaline
DO NOT
battery).
mix new and used batteries.
not in use for long periods. Always remove old, weak or worn-out batteries promptly and recycle or
dispose of them in accordance with local and national regulations.
Using the Speaker System
Adjusting the Transmitter
1. Turn on your audio source (for example, A/V receiver, MP3 player, stereo, etc.) and play
music at a normal listening volume.
2. Set the channel select switch on the back of the transmitter
Channel
to one of the transmitter's three broadcast frequencies: 1,
select
2 or 3. If you experience poor reception or interference, try
switch
choosing a different frequency by moving the channel select
switch to another position.
CHANNEL
DC IN
1 2 3
When the transmitter is receiving an audio signal and is
R AUDIO L
IN
ready, the SIGNAL indicator turns solid green.
Note
If the SIGNAL indicator on the transmitter does not turn on, please check the following:
(MP3 player, A/V receiver, etc.).
AC Power Adapters
1. Insert the small, round plug from the speaker AC
power adapter into the DC IN jack on the bottom of
the speaker.
2. Plug the other end of the speaker AC power adapter
into any standard 120V AC wall outlet.
DO NOT
leave batteries installed in the product when