3Doodler 2.0 매뉴얼 - 페이지 2

{카테고리_이름} 3Doodler 2.0에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3Doodler 2.0 4 페이지.
3Doodler 2.0에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지), 사용자 설명서 (10 페이지)

페이지 인쇄

LED LEGEND:

Solid RED:

Heating up

(please wait)

BLUE:

ABS

(230°C to 240°C;

446°F to 464°F)

GREEN:

PLA

(190°C to 200°C;

374°F to 392°F)

Flashing LED:

Reversing plastic

Actual product may vary from the image found in this document.

USING YOUR 3DOODLER 2.0

Step 1: Connect your 3Doodler 2.0 to the power adapter

Connect the power adapter to the back of the 3Doodler and plug it

into a power source.

Note: If you have also purchased the 3Doodler JetPack

can also connect this to the back of the 3Doodler as a power

source.

Step 2: Turn on the pen and select

your plastic/filament

Turn the pen on by selecting the correct

heating temperature for the type of

plastic/filament you are using. Set the

slide switch to HI ("High") for high

temperature plastics/filaments like ABS or

FLEXY, or LO ("Low") for low temperature

plastics/filaments like PLA.

3Doodler 2.0

WARNINGS & NOTICES

ENGLISH

you

Step 3: Allow your 3Doodler to heat up before loading

plastic/filament

The 3Doodler takes approximately 2 minutes to heat up. During

that time the LED indicator will be RED and it will not be possible to

use the pen. Once the correct melting temperature is reached and

the pen is ready, the LED indicator will change to BLUE (HI) or

GREEN (LO).

BLUE = HI ("HIGH") ABS and FLEXY (heating range

between 230°C and 240°C; or 446°F and 464°F)

GREEN = LO ("LOW") PLA (heating range between

190°C and 200°C; or 374°F and 392°F)

Step 4: Load the pen

Load the plastic/filament into the plastic loader

the pen, feeding it down the length of the 3Doodler until you feel it

gripped by the gears inside the pen. It can take up to 30 seconds

for a newly loaded strand to begin extruding from the nozzle of

the pen.

NOTE: If you do not feel the plastic/filament being gripped

by the gears inside the pen, please give the plastic a

gentle clockwise twist while pushing it down the shaft of

the 3Doodler.

Step 5: Extrude/select your speed

Simply single-click on the desired

extrusion speed (FAST (3) or SLOW (4) )

and your 3Doodler will continuously

extrude plastic/filament for up to ten

minutes before stopping.

To stop the continuous flow of

plastic/filament, simply click on either the

FAST (3) or SLOW (4) button on your

3Doodler.

If the pen stops and the RED LED appears again, wait a moment

for the LED to change to the appropriate color again (the pen is

simply returning to its optimal heating temperature).

NOTE: After 5 minutes of inactivity the 3Doodler's heating

system will automatically power down. You will need to

press one of the buttons OR toggle the slide switch off

and then on again to continue use.

3Doodler 2.0

WARNINGS & NOTICES

ENGLISH

at the back of

Plastic/filament