3Doodler Create+ 사용자 설명서 - 페이지 9

{카테고리_이름} 3Doodler Create+에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. 3Doodler Create+ 11 페이지.
3Doodler Create+에 대해서도 마찬가지입니다: 사용자 설명서 (16 페이지)

페이지 인쇄

Reverse and

remove plastic

correctly

TAKE A

BREAK:

Treat your

Nozzle right

Specifications are subject to change and improvement without notice.

SPECIFICATION OF POWER ADAPTER

Input: 100-240V AC, 0.5A MAX, 50-60Hz

Output: +5V DC, 1.2A

CARE & MAINTENANCE

For care and maintenance information, and

more advice on how to use your 3Doodler

Create+, please refer to our website:

the3Doodler.com To troubleshoot, please visit:

the3Doodler.com/troubleshooting

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user's authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If

02/2022

•

DO NOT pull plastic from the back of the 3Doodler Create+

other than as directed.

GREEN

Light

With the Pen set to

PLA

wait for

the

GREEN

light to come on.

Give your 3Doodler Create+ a rest after every 2 hours of continuous

Doodling. 30 minutes of down time should be plenty.

•

If you ever remove your nozzle, ONLY remove the nozzle

when your pen is heated and a BLUE/

DO NOT remove it when your 3Doodler Create+ is cold.

•

If you ever need to tighten your Nozzle, DO NOT force the

Nozzle or overtighten it, as you could break the Nozzle and

permanently damage your 3Doodler Create+.

SPECIFICATIONS

Output Power: 6W

Output Voltage: 5V

Input Voltage: 5V

CARE & MAINTENANCE

For care and maintenance information, and more advice on how to use your

3Doodler, please refer to our website: the3Doodler.com

To troubleshoot, please visit: the3Doodler.com/troubleshooting

LIMITED WARRANTY

For more details on your limited

warranty, please visit:

LIMITED WARRANTY

the3Doodler.com/warranty

For more details on your limited warranty, pleae visit:

For 3Doodler's Terms and Conditions

the3Doodler.com/warranty

and other notices please refer to

For 3DoodlerÕs Terms and Conditions and other notices please refer to our

website: the3Doodler.com/terms-and-conditions

our website: the3Doodler.com/

terms-and-conditions

This marking indicates that this product should not be disposed of with

other household wastes. To prevent possible harm to the environment or

human health from uncontrolled waste disposal, recycle it responsibly to

promote the sustainable reuse of material resources.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

SECTION 4: TIPS & BEST PRACTICES

Flashing

GREEN

Double click either speed

button and the LED light will

start flashing to signal the

plastic is reversing.

GREEN

light is showing.

this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help.

CAN ICES-3 (B)/NMB-3(B)

Once the Plastic stops reversing,

it is safe to remove it from the

pen by gently pulling on the

back of the strand.

GREEN

BLUE

Light

This marking indicates that this

product should not be disposed of with

other household wastes. To prevent

possible harm to the environment

or human health from uncontrolled

waste disposal, recycle it responsibly

to promote the sustainable reuse of

material resources.