3Doodler Start 문제 해결 매뉴얼
{카테고리_이름} 3Doodler Start에 대한 문제 해결 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3Doodler Start 1 페이지. Kids 3d pen
페이지 인쇄
1
Begin by charging your 3Doodler
Start to ensure the motor is able to
run at full power. This will take 45
minutes to 2 hours. Do not use the
3Doodler Start while charging.
The light will flash orange while
charging, and will turn solid orange
once it is fully charged.
DOES THE LIGHT TURN ON?
WAIT TO FEED
Insert a strand of plastic in the
Feed Port, and click the Feed
Button once to begin feeding
the filament. It takes 30-40
seconds for the plastic to
feed through.
INSERT PLASTIC
Feed the plastic and gently turn
it a quarter turn clockwise,
ensuring the plastic is gripped
by the gears. If the strand is
too short, insert another and
push it through.
PROBLEM SOLVED?
YES
NO
x2
REVERSE PLASTIC OUT
Try reversing the plastic by
double clicking on the feed
button, and pulling the
filament out of the Feed Port.
PROBLEM SOLVED?
YES
LED LIGHT
LED LIGHT
COLOR
COLOR
LED LIGHT
LED LIGHT
SOLID
SOLID
SLOWLY
SLOWLY
FLASHING
FLASHING
QUICKLY
QUICKLY
FLASHING
FLASHING
Troubleshooting Guide
Before You Begin, Note the Following Steps:
Once you turn the pen on, and click
the feed button, it takes 30-40
seconds for extrusion to begin after
first inserting a plastic strand.
START
Let your 3Doodler Start
charge fully before use.
Do not use the pen while
charging. Once it is charged,
turn the pen on.
YES
NO
IS THE CABLE WORKING?
If lights aren't displaying while
charging, please try another micro
USB cable to see if it is an issue
with the cable or the pen.
IS THE PLASTIC EXTRUDING?
Insert a strand of plastic in the
Feed Port, and click the Feed
Button once to begin feeding the
REMOVING SHORT FILAMENT
Put the pen in reverse mode while
NO
gently knocking the pen (with the
Feed Port facing down) on a surface
to dislodge the plastic strand.
PROBLEM SOLVED?
LED Lights Cheat Sheet
LED Lights Cheat Sheet
RED
RED
Your pen is
Your pen is
warming up
warming up
Please Contact
Please Contact
Customer Service
Customer Service
Please Contact
Please Contact
Customer Service
Customer Service
Still having issues?
(US) 718.618.9904
Please have your serial number ready for us. You can find
it printed on the bottom of your pen.
2
NO
YES
filament.
YES
NO
NO
YES
Have Fun
Doodling!
GREEN
GREEN
Pen is
Pen is
heated up / idle
idle
Plastic is
Plastic is
feeding
feeding
Plastic is
Plastic is
reversing
reversing
3
Push the plastic down the pen and
gently twist it clockwise to get it to
engage with the pen's gears. You will
feel it lock into place.
3Doodler Start Tips
Clogs and feed issues may be
prevented by clearing out all filament
from the pen in between uses, either
by reversing the filament out or by
finishing the strand you're using. We
strongly recommend this as a best
practice.
How-to and help videos on our
YouTube Channel:
YouTube.com/3DoodlerStart
45°
CUT STRAND AT 45° ANGLE
Try cutting off the tip of a new
piece of plastic at a 45° angle.
Insert that plastic into the pen
and run it through, pushing and
turning as necessary.
PROBLEM SOLVED?
YES
NO
PLEASE CONTACT
CUSTOMER SERVICE
ORANGE
ORANGE
Pen is fully
N/A
charged
Your Pen is
Your Pen is
low on battery
low on battery
Pen charging
N/A