Camille Bauer KINAX 2W2 운영 지침 - 페이지 4

{카테고리_이름} Camille Bauer KINAX 2W2에 대한 운영 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Camille Bauer KINAX 2W2 4 페이지. Programmable transmitter for angular position
Camille Bauer KINAX 2W2에 대해서도 마찬가지입니다: 운영 지침 (4 페이지)

페이지 인쇄

3. Place the measuring object in the end position, i.e. in the position, in which the

KINAX 2W2 should output 20 mA. Adjust with the virtual knob "Span" until the

output signal is correct.

4. Close the adjustment with the "Done" button.

The adjusting range of the zero position and span is 5%. If this range is not sufﬁ cient,

the span can be adapted by changing the mechanical characteristics (increase/

decrease the measuring span).

Simulation mode

The 2W2 conﬁ guration software supports the operation of the KINAX 2W2 in simu-

lation mode. The simulation of the measured value allows the subsequent chain of

devices to be tested during the installation phase.

Procedure:

1. Select the "Simulation" menu item under "Service" in the conﬁ guration software.

2. The window displays the device conﬁ guration. After the entry of the required

angle, the analog output is set in accordance with the device conﬁ guration.

9. Electric commissioning

• Provide a separate power supply for the device in case of consumer loads with

high interference levels.

• Install the entire plant in an EMC-compatible manner. Installation environment

and wiring can affect the EMC of the device.

• For Versions with explosion protection:

The regulations according to EN 60079-14, the equip-

ment safety law, the generally acknowledged rules of the

industry and these operating instructions are applicable for

installation and operation.

10. Maintenance

The device is free of maintenance. Repairs may only be carried out by autho-

rized authorities.

11. Speciﬁ cation and ordering information

Signiﬁ cance of the digits 1. to 12.

Description

Version of the transmitter

Standard, measuring output non intrinsically safe

Ex ia IIC T6, ATEX

Measuring output intrinsically safe

Mechanical angle range

Angle range up to 50

Angle range > 50 to 350

Drive shaft

Standard, dia. 2 mm [0.078 ʺ ] at front, length 6 mm [0.236ʺ]

Special, dia. 2 mm [0.078ʺ] at front, length 12 mm [0.472ʺ],

dia. 2 mm [0.078ʺ] at rear, length 6 mm [0.236ʺ]

Special, dia. 6 mm [0.236ʺ] at front, length 12 mm [0.472ʺ]

Special, dia. 6 mm [0.236ʺ] at front, length 12 mm [0.472ʺ],

dia. 2 mm [0.078ʺ] at rear, length 6 mm [0.236ʺ]

Special, dia. 1/4˝ at front, length 12 mm [0.472ʺ]

Special, dia. 1/4˝ at front, length 12 mm [0.472ʺ] ,

dia. 2 mm [0.078ʺ] at rear, length 6 mm [0.236ʺ]

Output variable

Current, 4 to 20 mA, 2-wire connection

Electrical connection

Connection to soldering terminals

Connection to screw terminals

Test certiﬁ cate

Without test certiﬁ cate

Test certiﬁ cate in German

Test certiﬁ cate in English

Conﬁ guration

Basic conﬁ guration, programmed

Programmed to order

Programmed to order, with zero position mark on the

drive shaft disk

Sense of rotation

Programmed for sense of rotation clockwise

Programmed for sense of rotation counter-clockwise

Programmed for V-characteristic

Description

Measuring range

[°angle], 0 to ﬁ nal value

V characteristic[±°angle], Min.:

Line 9: Admissible values

Final value ≥ 10 to 50° with selected angle range 50°

> 50 to 350° with selected angle range 350°

Switching point > ﬁ nal value, max. 60° with angle range 50°

> ﬁ nal value, max. 360° with angle range 350°

Line Z: Admissible values

Minimum value [±°angle] ≥ 0

Maximum value [±°angle] ≤ 25° with angle range 50°, span

(max.-min.) ≥ 5°

> 25° to 175° with angle range 350°, span ≥ 25° symmetrical

about the center line, e.g. [±°angle],

min. value = 15, max. value = 120,

correspond -120 to -15 to 0 to 15 to 120° (input) and +20 to

4 to < 4 to 4 to +20 mA (output)

10.

Characteristic of output variable

Linear

Function X to the power 1/2

Function X to the power 3/2

Function X to the power 5/2

Customized (give an algorithm or ﬁ xed points (23 for the

complete output range))

Lines 1 to 4: Not possible with V-characteristic (line 2 in

feature 8, sense of rotation)

11.

Climatic rating

Standard climatic rating

(annual mean relative humidity ≤ 90 %)

Improved climatic rating

(annual mean relative humidity ≤ 95 %)

12.

Marine Version

Without

Order

code

760-

Order

code

Switching

point:

Max.: