Alto-Shaam 500-1D 작동 및 관리 매뉴얼 - 페이지 4

{카테고리_이름} Alto-Shaam 500-1D에 대한 작동 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Alto-Shaam 500-1D 14 페이지. Cabinet, food holding - drawer warmers
Alto-Shaam 500-1D에 대해서도 마찬가지입니다: 사양 시트 (2 페이지), 브로셔 (4 페이지)

페이지 인쇄

WARMING CABINET CHARACTERISTICS

The cabinet is equipped with a special, low-heat-density,

heating cable. Through the HALO HEAT concept, the heat-

ing cable is mounted against the walls of the warming com-

partment to provide an evenly applied heat source controlled

by a thermostat. The design and operational characteristics

of the cabinet eliminates the need for a moisture pan or a heat

circulating fan. Through even heat application, the quality of

a food product is maintained up to as much as

several hours.

T H E R M O S TAT

P I L O T L I G H T S E Q U E N C E

Whenever the thermostat is turned up, the pilot light will

indicate the power ON/OFF condition of the heating cable,

and consequently, the cycling of the cabinet as it maintains

the dialed cavity temperature. If the pilot light does not indi-

cate after normal start-up, the main power source, thermo-

stat, and/or the pilot light must be checked. If a warming

compartment does not hold the temperature as dialed, the

calibration of the thermostat must be checked. (See the para-

graph on thermostat calibration.) If a warming compartment

fails to heat or heats continuously with the thermostat OFF,

the thermostat must be initially checked for proper operation.

If all is in order, a continuity and resistance check of the heat-

ing cable should be made. (See the circuit

diagram.)

T H E R M O S TAT C A L I B R AT I O N

The thermostat is precision calibrated at the factory.

Normally, no adjustment or recalibration is necessary unless

the thermostat has been mishandled in transit, changed or

abused while in service. A thermostat with a sensing bulb

operates on hydraulic pressure. Consequently, any bending

of the bulb results in a change in its volume and displaces the

accuracy of the thermostat calibration.

A thermostat should be checked or recalibrated by plac-

ing a quality temperature indicator at the center of an empty

warming cavity. DO NOT CALIBRATE WITH FOOD PROD-

UCT IN THE WARMING CABINET. The temperature must

be allowed to stabilize at one particular setting for at least

one hour. Following this stabilization period, the center of

the thermal swing of the cavity temperature should approxi-

mately coincide with the thermostat setting.

The calibration screw of the thermostat is located in the

dial shaft, and should be adjusted with great care and cau-

tion. With the shaft held stationary, a minute clockwise

motion of the calibration screw APPRECIABLY lowers the

thermostat setting while a reverse, counter-clockwise motion

results in the opposite condition. After achieving the desired

cycling of the thermostat, the calibration screw must be

sealed in place with a few drops of sealant.

[

R E D N A I L P O L I S H O R E Q U I V A L E N T I S A C C E P T A B L E

10/13/98

A N D

10. THERMOSTAT

11. HEAT INDICATOR LIGHT (125V)

12. TEMPERATURE GAUGE

13. CASING ASSEMBLY

14. INSULATION: 22" x 43" (559mm x 1092mm)

15. CABLE CONNECTION HARDWARE

16. FAN (125V)

17. HEATING CABLE: Length 104' (31699mm)

18. CABINET DRAWER RAIL ASSEMBLY

19. CABINET DRAWER RAIL ASSEMBLY

20. CABINET DRAWER RAIL ASSEMBLY

21. CABINET DRAWER BEARINGS (

22. DRAWER PAN (

. ]

P E R A T I O N A N D

A R E

S E R V I C E V I E W PA R T S L I S T S

M O D E L 5 0 0 - 1 D

PART DESCRIPTION

1. TOP

2. TOP MOUNTING SCREWS

3. POWER CORD (125V)

CORD SET: 230V INTL (TYPE HO7 RN-F)

CORD SET: 208-240V)

4. POWER CORD STRAIN RELIEF BUSHING

INLET (208-240V)

INLET (230V)

5. CASING BACK

6. CASING BACK MOUNTING SCREWS

7. DRAWER ASSB.

DRAWER ASSB. W/VENTS (

E A C H A S S E M B L Y I N C L U D E S

— DRAWER PULL

— PAN SPACERS

— PAN SPACER MOUNTING SCREWS

— DRAWER BEARINGS

8. DECOR PANEL (125V) 500-1D

DECOR PANEL (208-240V) 500-1D

9. WATTAGE SWITCH (125V only)

HEAT INDICATOR LIGHT (208-240V,230V)

FAN (208-240V,230V)

FAN BLADE

(

)

NOT SHOWN

MOUNTING STUD (

NOT SHOWN

MOUNTING NUT (

NOT SHOWN

DISCONNECT UNIT FROM POWER

SOURCE BEFORE CLEANING

OR SERVICING

# 8 1 8 • 3

A N U A L

QUANTITY ALTO-SHAAM

PER UNIT

(125V)

)

OPTION

NOT SHOWN

)

NOT SHOWN

)

PART NO.

11369

SC-2459

CD-3232

CD-3984

CD-3858

BU-3011

IT-3857

IT-33173

11380

SC-2459

5303

15418

PL-2005

11398

SC-2459

BG-2410

5744

5743

SW-3409

TT-3057

LI-3027

LI-3951

GU-33384

4336

IN-2381

FA-3485

FA-3342

FA-3343

CB-3044

5331

ST-2547

NU-2437

BG-2410

PN-2123