DivioTec NBR225P 빠른 매뉴얼
{카테고리_이름} DivioTec NBR225P에 대한 빠른 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DivioTec NBR225P 2 페이지. Full hd multi-streams extreme wdr compact bullet ip camera
DivioTec NBR225P에 대해서도 마찬가지입니다: 사용자 설명서 (17 페이지)
페이지 인쇄
This guide is for quick installing and connecting the Full HD Multi-Streams Extreme WDR Micro Bullet IP Camera. For
more details, please refer to the User's Manual of the camera in the supplied CD.
MicroSD Card Slot / Default Button
The position of the microSD card slot and the default button are shown as below.
microSD Card Slot
Insert the microSD card into the card slot to store videos and snapshots. Do not remove the microSD card when the
camera is powered on.
NOTE: It is not recommended to record with the microSD card for 24/7 continuously, as it may not be able to
support long term continuous data read/write. Please contact the manufacturer of the microSD card for
information regarding the reliability and the life expectancy.
Default Button
Press the button with a proper tool for at least 20 seconds to restore the system.
IP Camera Installation
Please follow the instructions below to complete IP Camera installation.
Power up the Camera
To power up the IP Camera, please plug the camera's DC 12V Cable into the power terminal block. Alternatively,
users can power the camera by PoE. Refer to the following section to connect Ethernet Cable for PoE connection.
NOTE: If PoE is used, make sure Power Sourcing Equipment (PSE) is in use in the network.
Ethernet Cable Connection
Connect one end of the CAT5 Ethernet Cable to the RJ-45 connector of the IP Camera, and the other end of the cable
to the network switch or PC.
NOTE: In some cases, Ethernet Crossover Cable might be needed when connecting the IP Camera directly
to the PC.
NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check
the LAN connection.
Full HD Multi-Streams Extreme WDR Compact Bullet IP Camera Quick Guide
Vari-Focal Lens
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
Function Cables
RJ-45 & DC 12V Cable
No.
Connector
1
RJ-45
For network and PoE connections
2
Power Jack (DC 12V)
Power connection
Before Login to the Camera
A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the
camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and
plug-ins or setting Internet's security level to default. For further details, please refer to the User's Manual in the
supplied CD.
ActiveX Controls and Plug-ins Settings
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>, and click on <Custom level> to
change ActiveX settings.
Step 4: Set "ActiveX controls and plug-ins" items to
<Prompt> or <Enable>.
Camera Login
The default IP address of the camera is: 192.168.0.250. Therefore, to access the camera for the first time, please set
the IP address of the PC as: 192.168.0.XXX; for example:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Login ID and Password
Key in the camera's IP address in the URL bar of the web browser window and hit on "Enter".
Enter the default username (Admin) and password (1234) in the prompt request dialogue. Note that username is
case sensitive.
Install the ActiveX Control
After connecting to the camera, the request for installing the ActiveX control will appear just below the URL bar.
Right click on the information bar, and then click on <Install ActiveX Control...> to permit ActiveX control
installation.
Definition
Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>.
Step 4: Down the page, click <Default Level> and click
on <OK> to confirm the setting. Close the
browser window, and open a new one later for
accessing the IP camera.