esera automation 11220 V2 사용자 설명서 - 페이지 3
{카테고리_이름} esera automation 11220 V2에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. esera automation 11220 V2 6 페이지. 8-fold switch module with button inputs for 1-wire bus
페이지 인쇄
Art. No. 11220 V2
6
Conformity
EN 50090-2-2,
EN 61000-4-2, ESD
EN 61000-4-3, HF
EN 61000-4-4, Burst
EN 61000-4-5, Surge
EN 61000-6-1, Fault-free operation
EN 61000-6-3, Stray radiations
RoHS
7
Operating mode, display and control
The module has two modes of operation: normal mode and manual control mode.
Normal mode: After start-up, the device is in normal operation mode. This means that a command is applied
directly by the 1-Wire interface to the appropriate output relay. The respective output LED is lit.
Manual control mode: By pressing the button „MAN/Select" for 2 seconds, the module switches to manual
control mode (manual operation). The „PWR" LED flashes to confirm selection of manual control mode.
By briefly pressing the "MAN/Select" button an output will be selected. LEDs 1 - 8 light up for the selected output.
With the „ON/OFF" button, selected output will be switched on or off.
It is also possible to switch desired number of outputs in one cycle.
After a waiting period of approximately 2 seconds, the device switches automatically into „Normal mode"
operation. The „PWR" LED lights up again permanently and selected outputs are activated.
Delete „Manual control mode": By pressing the „ON/OFF" button for 2 seconds, outputs selected in the manual
control mode will be switched off.
Indicator
Designation
LED 1-8
Output 1-8
LED PWR
Power
LED Status
Status display
manual control
mode
Button
Designation
MAN/Select
Operating mode /
Channel selection
ON/OFF
Output 2 On/Off
8
8-fold digital input, pushbutton interface
Besides the manual control mode (module top face) and the 1-Wire interface, the module also has an
8-Fold Pushbutton Interface (8 x Digital Input) to switch the outputs.
To switch an output, a brief input signal (pressing the button) on the respective input is sufficient.
The 8-fold pushbutton interface is designed to switch lightings or sockets in the living area by e.g. light switches
or motion detectors with pulse output. This ensures fast switching even with no system control available.
The impulse control, comparable to a staircase lighting timer, allows any number of light sensors and motion
detectors to be connected at the same time.
Further details on the ESERA automation lighting system can be found on the following website:
https://www.esera.de/smart-home/anwendungsbeispiele/lichtsteuerung/
All rights reserved. Reproduction as well as electronic duplication of this user guide, complete or in part, requires the written consent of
ESERA-Automation or E-Service GmbH. Errors and technical modification subject to change. ESERA-Automation, E-Service GmbH 2018
www.esera.de
LED function
- LED is lit for 2 seconds on system start-up
- Normal mode: LED display is lit when the output is active
- Manual control mode: Select the output to be switched on or off
with the „Select" button
- LED is lit for 2 seconds on system start-up
- LED is lit when an output relay is active
- LED flashes in the manual control mode
- LED is lit for 2 seconds on system start-up
- Status display of the selected output after switch to normal mode
operation (relay on or off)
Button function
The button has two different functions
- Switch to manual control mode (press for 2 seconds)
- Select output (press briefly)
The button has two different functions
- Selected output On / Off (press briefly)
- Delete all outputs of manual control mode (press for 2 seconds)
11220 V1.0_R1.1 Manual 8-Fold Switch Module
Page 3 of 6