1 BY ONE 1-AD07US01 사용 설명서 - 페이지 8

{카테고리_이름} 1 BY ONE 1-AD07US01에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. 1 BY ONE 1-AD07US01 14 페이지. Belt drive turntable system

페이지 인쇄

Windows:

1. By the system clock, right-click over the Speaker icon select Sounds then

the Recording tab, and then click on the USB device in the list and click

Properties. Click the Advanced tab set your required bit rate and sample rate

from the Default Format dropdown (normally "2 channel 16-bit 44100 Hz").

2. On the Advanced tab, in the "Default Format" section, make sure the

dropdown menu is set to "2 channel 16-bit 44100 Hz".

For a more detailed walk-through of the above steps for Windows ( or if that does

not work for your version of Windows ), see Windows: accessing the Windows

Sound controls.

Mac:

1. From Apple Menu > System Preferences select "Sound" and click on the Input

tab

2. Select "USB Audio CODEC" or similar as the input device and verify the

Recording Meter shows input.

3. If the recording meter in the Sound preferences panel does not show input:

1. From the Finder, select Go > Utilities and open Audio MIDI Setup.

2. If the Audio Devices window is not visible, select Window > Show Audio

Devices.

3. Select your USB input device in the list in the left pane of the Audio Devices

window.

4. Set the Format to "44100.0 Hz" and "2ch-16bit".

For a more detailed walk-through of the above steps for Mac , see Mac and USB

input devices on the Audacity Wiki.

2.3 Launch Audacity.

If Audacity is already running when you connected the cable, choose Transport

>Rescan Audio Devices or restart Audacity.

2.4 Project Rate

Set the Audacity Project Rate in Selection Toolbar at the bottom left of the

Audacity screen to 44100 Hz :

2.5 Devices

Use Device Toolbar to set the recording and playback devices and to set the

recording channels to "2 (Stereo) Recording Channels", as in the below example on

Windows 10

• The Recording Device is set to the USB device (in this case the device name, but

often called or including the phrase "USB Audio CODEC").

• Recording Channels is set to stereo.

• The Playback Device is set to the named speakers of the built-in computer sound

device.

• These settings can also be changed in Devices Preferences.

Windows calls most USB external devices "microphones". Some higher-end USB

recording interfaces may appear as their explicit manufacturer's name.

3. Software Playthrough

Use Transport > Transport Options > Software Playthrough (on/off) and click

"Software Playthrough" to turn it "on" (the checkmark is shown when it is "on").

This setting can also be enabled or disabled in Recording Preferences. Software

Playthrough lets you hear the turntable through the computer speakers when

recording. It also lets you hear the turntable without recording if you turn on

monitoring (see the next section below).

4. Monitoring

Enable monitoring to set the recording level

• Turn monitoring on by clicking once on the microphone icon in the Recording

Meter.

• In Mixer Toolbar, turn up the left-hand playback volume slider (by the speaker icon).

• The right-hand recording volume slider (by the microphone icon) can often be used

to vary the loudness of the recording, but it may not function with all turntables.

If it does not, try adjusting the output level on the turntable (often, there is a gain

control under the chassis).

Alternatively, you may be able to adjust the input level on Windows and Linux only,

usually by looking for the speaker icon by the system clock. On

click over the speaker icon > "Recording Devices". Then right-click over USB

Audio Codec, choose "Properties" and click the Levels tab.

• Try to aim for a maximum peak of around –6 dB, which corresponds to

around 0.5 on the waveform. You can always boost the level later with Effect

> Amplify... or Effect > Normalize... after you have completed editing.

Windows, right-