ClearOne CLOCKAUDIO TS-001 기술 노트 - 페이지 6
{카테고리_이름} ClearOne CLOCKAUDIO TS-001에 대한 기술 노트을 온라인으로 검색하거나 PDF를 다운로드하세요. ClearOne CLOCKAUDIO TS-001 6 페이지. Using the clockaudio ts-001 with the converge pro
페이지 인쇄3.
In Command Editor select the appropriate Unit Type and DID then choose command of
a.
If the touch pad is to act as a toggle switch (press the switch once, the channel mutes, press it again and the channel un-mutes), choose
Mode 2. Advance to step 6 below.
b.
If the touch pad is to act as a push to talk switch (press and hold the switch to un-mute, talk, release to mute) choose Mode 0.
c.
If the touch pad is to act as a push to mute (press and hold to mute, release to unmute) choose Mode 1.
d.
Click the Apply button located in the lower-right.
Inactive (High) Command
4.
Click on the
5.
In Command Editor select the appropriate Unit Type and DID then choose command of MUTE, Channel 1 and Group M:
a.
If the touch pad is to act as a push to talk switch, choose Mode 1.
b.
If the touch pad is to act as a push to mute switch, choose Mode 0.
c.
Click the Apply button located in the lower-right.
6.
Select Control Port A and Select Pin 2.
7.
Click on the Active (Low) Command button.
8.
In Command Editor choose command of MUTE, Channel 1 and Group M, and Mode 0 from the pull-down lists. When microphone Channel
1's Mute state is OFF, Pin 2 will be pulled low to ground and the green LED"S will illuminate. Click the Apply button located in the lower-right.
9.
Click on the Inactive (High) Command button.
10. In Command Editor choose command of MUTE, Channel 1 and Group M, and Mode 1 from the pull-down lists. When microphone Channel
1's Mute state is ON, Pin 2 will go high or float and the green LED's will turn off. Click the Apply button located in the lower-right.
11. Select Control Port A and Select Pin 4
12. Click on the Active (Low) Command button.
13. In Command Editor choose command of MUTE, Channel 1 and Group M, and Mode 1 from the pull-down lists. When microphone Channel
1's Mute state is ON, Pin 10 will be pulled low to ground and the red LED"S will illuminate. Click the Apply button located in the lower-right.
14. Click on the Inactive (High) Command button.
15. In Command Editor choose command of MUTE, Channel 1 and Group M, and Mode 0 from the pull-down lists. When microphone Channel
1's Mute state is OFF, Pin 4 will go high or float and the red LED's will turn off. Click the Apply button located in the lower-right.
Note: For Microphone 1, Control Pin 1 and Status Pins 2 and 4 will be used. For Microphone 2, Control Pin 5 and Status
»
Pins 6 and 8 will be used. For Microphone 3, Control Pin 9 and Status Pins 10 and 12 will be used. For Microphone 4,
Control Pin 13 and Status Pins 14 and 16 will be used.
HEADQUARTERS:
Salt Lake City, UT USA
5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116
Tel: 801.975.7200
Toll Free: 800.945.7730
Fax: 801.977.0087
E-mail: [email protected]
button.
.
EMEA
Tel: 44 (0) 1189.036.053
E-mail: [email protected]
© 2012 ClearOne. All rights reserved. Other product names may be trademarks of their respective owners.
Specifications subject to change without notice. 801-000-000-05 Rev. 1.1 - November 2012.
APAC
Tel: 801.303.3388
E-mail: [email protected]
MUTE
, Channel 1 and Group M:
LATAM
Tel: 801.974.3621
E-mail: [email protected]
TechSales
Tel: 800.705.2103
E-mail: [email protected]
Technical Support
Tel: 800.283.5936
E-mail: [email protected]