ClearOne WS800 빠른 시작 매뉴얼 - 페이지 7

{카테고리_이름} ClearOne WS800에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ClearOne WS800 10 페이지. Wireless microphone system antenna application guide
ClearOne WS800에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (15 페이지), 매뉴얼 (5 페이지), 빠른 시작 매뉴얼 (13 페이지), 애플리케이션 매뉴얼 (12 페이지), 애플리케이션 매뉴얼 (11 페이지)

페이지 인쇄

1. How to Sync Transmitters with the Receiver

Transmitters:

HAND-HELD:

1. Heads: Five (5) microphone condenser elements are available. In general, condenser heads are more

"transparent" and do not require the microphone to be held as close to the mouth.

2. Display: OLED display is used to program and display the current status of the transmitter functions.

3. Switch: User programmable to toggle on/off, on/mute/ or on/on.

4. Battery and Control Cover: Unscrew counter-clockwise and gently slide open.

5. Antenna Cover: Do not hold the antenna cover. Your hand will shield the RF signal and cause poor audio

performance.

6. IR Sensor Port: The IR sensor is used to transfer channel settings and a random encryption key from the

receiver to the transmitter.

7. Select button: Press this button to select a function. The first press activates the first edit able function in the

tree. Press again to move to the next edit able function.

8. Parameter Up: Press this button to increase the value of the selected function.

9. Parameter Down: Press this button to decrease the value for the selected function.

10. USB Port: Plug a micro USB cable into the USB port to charge the batteries or upgrade the firmware.

11. Batteries: (not shown) AA NiMH, 2200 to 2500-mAHr recommended.

12. Battery Door: Open position.

BELT PACK:

1. Antenna: Length and style varies with the transmitters model number. Antennas are field replaceable to

improve reliability and redundancy.

2. Programmable Switch: Toggle on/off, on/mute/ or on/on.

3. Microphone Connector: TA4 mini XLR style: ClearOne offers a full range of lavaliere and headset mics for

optimal performance of your ClearOne transmitter. Works with both snap in and screw-in microphones.

4. Display: OLED display is used to program and display the current status of the transmitter functions.

5. IR Sensor Port: The IR sensor is used to transfer channel settings and a random encryption key from the

receiver to the transmitter.

6. Select: Press this button to select a function. The first press activates the first edit able function in the tree.

Press again to move to the next edit able function.

7. Parameter Down: Press this button to decrease the value for the selected function.

8. Parameter Up: Press this button to increase the value of the selected function.

9. Batteries: AA NiMH, 2200 to 2500-mAHr recommended.

10. Battery Door Locks: To open, press both at the same time and lift the door open. To close, snap the door closed.

11. USB Port: Plug a micro USB cable into the USB port to charge the batteries or upgrade the firmware.

12. Belt-Clip: Spring-loaded clip for attaching the transmitter to a belt or similar object. Spring pressure presses

the clip into two holes in the transmitter body. Pull them out to remove or reverse the clip. Exercise caution to

prevent injury or scratching the case.

13. Contacts: Charging contact points for the docking station.

6 7 8