Altrad AFBM 160 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} Altrad AFBM 160에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Altrad AFBM 160 2 페이지.

페이지 인쇄

TECHNICAL DATA

Mixer type

Dimensions

Mixer weight

Operating capacity

Voltage (alternating)

Rated power (S6 10%)

Rated current

Mixer noise emissions (empty)

PREPARATION OF THE MIXER FOR OPERATION

1. MIXER ASSEMBLY

The mixer is folded at delivery. Before startup, lift it into the operating position. After the packaging

has been removed, loosen the nuts (4). First, hold the mixer by the cabinet (33), lift it and at the same time open the

wheel assembly (5) and fix it. Then, lift the mixer from the front. Grab it by the handle (9) and extend the support

leg (1) during the lifting move. Make sure that the mixer does not collapse. After the mixer has been setup in the

operating position, tighten the nuts

(4). The assembly needs to be performed carefully otherwise the mixer could collapse when loaded or transported.

2. ELECTRICAL CONNECTION OF THE MIXER

Connect the mixer to the electrical grid with a cable that has a minimum cross-section of 3×1.5mm

is suitable up to the length of 25m. If the power cable is longer, the cross-section must be 3×2.5mm

the connection of the mixer must be equipped with a 10A fuse. No additional electrical motor protection is necessary

since the motor has an integrated thermal sensor. The sensor is connected to the switch that automatically stops the

operation of the electrical motor in case of overheating.

3. MIXER OPERATION

Place the mixer on level and firm ground to prevent sinking or

capsizing.

The maximum slope of the ground is 10° as shown on the picture

below. The acceptable slope of 10° means the deviation of the

water level 88mm from the edge of the cabinet.

Connect the product to the electrical grid with an undamaged extension cord that must be extended and laid in

order to prevent damage.

Start the mixer with the switch that can only be turned on if there is voltage on the terminals. Every time the electrical

current is interrupted, the switch is turned off. If you wish to restart the mixer, push the start button again every time the

voltage is restored. Place the mixer drum into the position suitable for the material you wish to mix (more vertically for

mortar, more horizontally for concrete). After this operation has been completed, the drum can be filled. Only fill the drum

up to its maximum operating capacity.

We suggest the following order of filling: First, pour part of the water into the drum, add half of the sand and all the

additional material (such as cement, lime...). After the contents have been mixed slightly, add the remaining water and

sand.

WARNING: After the first couple of mixing cycles, water can start leaking at the joint between the cover and

bottom of the vessel.

Only a rotating drum can be filled and emptied! The mixer can be transported within the construction site by means

of wheels and a handle. During transport, the drum opening must face upwards.

safety, please also observe the instructions of the manufacturers of additional materials (cement, lime, etc.).

4. CLEANING AND MAINTENANCE

Before every cleaning or repair, do not forget to

unplug the mixer from the electrical grid

Cleaning extends the service life of the mixer therefore it must be as thorough as possible. Wash the external surfaces

of the mixer with flowing water and a soft brush. Do not scratch the mortar with sharp objects as you might damage the

coated surfaces. Rinse the inside of the drum immediately after work with a pressurized water jet in order to remove all

the remains of the mixed material.

The mixer maintenance is simple and reduced to a minimum:

Periodically check if the bolts and nuts are tightened sufficiently

Regularly check the tension of the drive belt and re-tension it if necessary. Re-tension it by loosening the two nuts on

the bolts used to attach the electrical motor cabinet to the frame and pushing the electrical motor together with the

cabinet down. Tighten the nuts. Only qualified persons with original spare parts can perform any repairs of the mixer.

AFBM 160

height

(mm)

1340

folded height

(mm)

870

length

(mm)

1140

width

(mm)

720

(kg)

(l)

145-150

(V)

230

(W)

700

(A)

2.7

(dBA)

. This cross-section

. The socket for

In order to ensure complete operational

MIXER COMPONENTS

20. Crossbar

21. Bolt

1. Sprocket

M00040

22. Cogwheel

2. Drum

PL00066

23. Switch

3. Cover

M000439

24. Bearing

4. Bearing

M000115

25. Spring pin ø 6×45

5. Bolt M8×70

M000301

26. Bearing

6. Turning wheel

PL00119

27. Spring pin ø 6×45

7. Nut M12

M000137

28. Cabinet

8. Pipe clamp

PL00060

29. Drive shaft

9. Nut M8

M000131

30. Belt

10. Bolt M12×45

M000343

31. Pulley

11. Brake

M000344

32. Retaining ring

12. Spring

M000417

33. Cover

13. Brake rope

M000324

34. Bolt

14. Nut M12

M000137

35. Electric motor

15. Pedal

M000375

36. Bolt

16. Bolt M12×90

M000312

37. Bolt M8×70

17. Cover

M000435

38. Framework

18. Retaining ring z48

M000329

39. Wheel

19. Bearing

M000115

40. Axle guard

PL00099

M000285

M000443

M000242

M000114

M000278

M000114

M000332

M000434

PL00055

M000099

M000430

M000326

M000436

M000434

M000150

PL00062

M000301

PL00102

M000355

M000278