Altronix eBridge PLUS eBridge1PCRM 설치 매뉴얼 - 페이지 2

{카테고리_이름} Altronix eBridge PLUS eBridge1PCRM에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Altronix eBridge PLUS eBridge1PCRM 4 페이지. Ip and poe+ over coax solution

페이지 인쇄

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local

codes and authorities having jurisdiction. Wiring should be UL Listed and/or Recognized wire suitable for

the application.

eBridge1PCTX and eBridge1PCRM are not intended to be connected to outside plant leads and should be

installed indoors within the protected premises. eBridge1PCTX and eBridge1PCRM are intended for indoor

use only.

1. eBridge1PCRM installation:

a. Secure unit to desired mounting surface with a proper fastening device utilizing the unit's

mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity to ethernet switch/network,

NVR or video server.

Note: When installing more than one (1) eBridge1PCRM, please allow at least 1" (25mm)

distance between the receivers.

b. Connect structured cable from ethernet midspan or endspan device to RJ45 jack marked

[10/100BaseT] (Fig. 2, pg. 3).

c. Connect Coax cable to BNC connector marked [Coax] (Fig. 2, pg. 3).

d. A local AUX input 24VAC or 24VDC can be used to power the eBridge1PCRM. This will eliminate

the need for the eBridge1PCRM to draw power from the midspan/endspan, thus making the midspan/

endspan additional power available to the end PoE powered device.

2. eBridge1PCTX installation:

a. Secure unit to desired mounting surface with a proper fastening device utilizing the case's

mounting hole (Fig. 2a, pg. 3). Unit should be mounted in proximity of camera/device.

b. Connect structured cable from IP camera/device to RJ45 jack marked [10/100BaseT] (Fig. 2, pg. 3).

c. Connect Coax cable to BNC connector marked [Coax] (Fig. 2, pg. 3).

Note: eBridge1PCRMT is designed to accommodate Megapixel, HD720, HD1080, and VGA (SD) cameras.

It is important to note that some high resolution and high frame rate cameras may demand faster headend

processing ability, such as a PC graphics card to present a quality image. If the headend processing equipment

is insufficient in speed, the image may show pixelation and latency. It is advisable to pre-test system if unsure.

Alternatively, frame rate and resolution may be reduced to accommodate system equipment.

Parameter

Connections

Input power

requirements

Indicators

Environmental

Conditions

Regulatory

Compliance

Weights (approx.)

Fig. 1

eBridge1PCRM

Structured

Cable from

midspan/endspan

Coax

Cable from

eBridge1PCT or

eBridge1PCTX

- 2 -

www.a1securitycameras.com email: [email protected]

Installation Instructions:

Technical Specifications:

Description

BNC for Coax link. RJ45 for ethernet link.

Midspan or endspan port connected. AUX input for powering.

Blue: Coax Link.

Yellow (RJ45 connector): On - Link, Off - No Link, Blinking - Activity.

Green (RJ45 connector): On - 100Base-TX, Off - 10Base-T.

Green: Power.

Operating Ambient Temperature: UL60950-1

eBridge1PCRM:

-20ºC to 49ºC (-4ºF to 120.2ºF).

eBridge1PCTX:

For 15W:

-40ºC to 75ºC (-40ºF to 167ºF).

For 30W:

-40ºC to 49ºC (-40ºF to 120.2ºF).

Relative humidity:

85%, +/- 5%.

Storage Temperature: -30ºC to 70ºC (-22ºF to 158ºF).

Operating Altitude:

-304.8 to 2,000m.

UL/CUL Listed for Information Technology Equipment (UL 60950-1).

CE approved. C-Tick compliant.

Product: 0.4 lbs. (0.181 kg) | Shipping: 1 lbs. (0.45 kg).

Green LED

indicates

24VAC or

Yellow LED

indicates PoE

Blue LED

indicates

Coax Connection

Available from A1 Security Cameras

Power

Aux.

Structured

Cable from

24VDC

IP Camera/Device

Input

Coax

Cable from

eBridge1PCRM

eBridge1PCTX

Green LED

indicates

Power

Blue LED

indicates

Coax Connection

eBridge1PCRMT