Altronix NetWaySP1P 설치 매뉴얼
{카테고리_이름} Altronix NetWaySP1P에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Altronix NetWaySP1P 4 페이지. Powered media converter/injector
Altronix NetWaySP1P에 대해서도 마찬가지입니다: 설치 매뉴얼 (4 페이지), 설치 매뉴얼 (4 페이지), 설치 매뉴얼 (4 페이지)
페이지 인쇄
Altronix NetWaySP1P converts 10/100/1000 Mbps ethernet to Fiber (1000Base-X/SX/LX)
and provides PoE.
Agency Listings:
• UL/cUL Listed for Information Technology
Equipment (UL 60950-1).
• CE approved.
Input:
• 24VDC @ 1.5A, 56VDC @ 0.75A (30W).
• 24VDC @ 1.0A, 56VDC @ 0.5A (15W).
Fiber Port:
• One (1) 1Gb SFP port.
• Use with SFP module 1000Base-X (1Gb),
compliant to Class 1 laser product
(not included).
Ethernet:
• IEEE 802.3at (30W) compliant.
• Wire type: 4-pair CAT5e and higher.
• Connectivity: RJ45, auto-crossover.
• Speed: 10/100/1000Mbps.
• Distance: up to 100m.
Unit is powered via 24VDC-56VDC. NetWaySP1P is not intended to be connected to outside plant
leads and should be installed indoors within the protected premises.
1. Mount NetWaySP1P in desired location utilizing the mounting hole (Fig. 1a, pg. 2). Use a proper
fastener and/or wall anchor when securing NetWaySP1P with screw through its mounting hole to
the wall.
Note: Earth ground can be used, if needed, for high transient or outdoor environments.
If used, insert an Earth ground wire (included with product) into the internal ground
terminal until secured (a slight tug can check stability) & fasten the free end to a chassis
earth ground.
If earth ground is not attached and needed, refer to Fig.1b, pg.2 for manual placement.
2. Connect 24VDC-56VDC power source to terminals marked [24-56VDC – Input +].
Terminals accommodate up to 12 AWG wires.
3. Connect structured cable from port marked [PoE+ Output] on NetWaySP1P to a PoE device
(Fig. 2, pg. 2).
4. Connect fiber optic cable to a fiber SFP module. Connect the module to the port marked [SFP]
on the NetWaySP1P. Connect the other end of fiber cable to an SFP module of a remote device.
SFP LED will illuminate indicating data connection (Fig. 2, pg. 2).
NetWaySP1P
Powered Media Converter/Injector
Installation Guide
Overview:
Features:
Installation Instructions:
LED Indicators:
• Yellow and Green LEDs (RJ45 jack):
IP Link status, 10/100/1000 Base-T/active.
• Green Pwr In LED:
Indicates unit is powered.
• Green PoE LED:
Indicates PoE present.
• Green SFP (Fiber) LED:
Indicates SFP connection.
Environmental:
• Refer to Environmental Conditions on page 3.
Dimensions (W x L x H approx.):
3.375" x 3.8" x 1"
(85.7mm x 96.52mm x 25.4mm).