Cutters Edge CE807R-B1 Series 소유자 매뉴얼 - 페이지 4
{카테고리_이름} Cutters Edge CE807R-B1 Series에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cutters Edge CE807R-B1 Series 19 페이지. Rotary rescue saw
페이지 인쇄WARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD
DO
read this entire operator's manual before operating this
machine and understand all warnings, instructions, and
controls.
DO
keep all guards in place and in good condition.
DO
wear safety approved hearing, eye, head and respiratory protection.
DO
read and understand the symbol definitions contained in this manual.
DO
keep all parts of your body away from the blade and all other
moving parts.
DO
know how to stop the machine quickly in case of emergency.
DO
shut off the engine and allow it to cool before refueling.
DO
inspect the blade, flanges and shafts for damage before installing the
blade.
DO
use CUTTERS EDGE Diamond Blades, BLACK STAR
DIAMOND BLADE or BLACK LIGHTNING DIAMOND
BLADE. Specifically rated with a maximum operating speed of
5400 RPM on 14" (350mm) or 6200 RPM on 12" (300mm).
DO
use CUTTERS EDGE Diamond blades marked with a 1"
(25.4mm) hole for a 1" (25.4mm) flange, or a 20mm hole for a
20mm flange.
DO
use Cutters Edge diamond blades marked for use with gasoline-
powered, hand-held, portable, abrasive cut-off machines.
DO
read all safety materials and instructions that accompany any blade
used with this saw.
DO
inspect each blade carefully before using it. If there are any signs of
damage or unusual wear, DO NOT USE THE BLADE.
DO
verify the blade arbor hole matches the machine spindle before
mounting the blade.
DO
make sure the blade and flanges are clean and free of dirt and debris
before mounting the blade on the saw.
DO
use the correct blade for the type of work being done. Check with
blade manufacturer if you do not know if blade is correct.
DO
always hold the machine with both hands when the engine is
running. Use a firm grip with thumbs and fingers encircling the
handles.
DO
keep all parts of the body away from the cut-off blades when the
engine is running.
DO
keep the handles dry, clean, and free of oil or fuel.
DO
always carry the machine with the engine stopped and the muffler
away from the body.
DO
use caution and follow the instructions when loading the saw.
DO
operate this machine only in well ventilated areas.
DO
instruct bystanders on where to stand while the saw is in operation.
DO
establish a training program for all operators of this machine.
DO
clear the work area of unnecessary people. Never allow anyone to
stand in front of or behind the blade while the engine is running.
Do use caution when handling fuel!
DO
move the machine at least 10 feet away from the fueling point
before starting the engine and make sure the gas cap and the fuel cap
on the saw are properly tightened.
DO
use caution when lifting and transporting the machine.
DO
always check for buried electrical cables before sawing.
If unsure, contact the local utilities.
DO
have all service, other than items in this manual, performed by
competent service personnel.
DO
always tie down the Rotary Saw when transporting.
DO
use caution and follow instructions when setting up or transporting
the machine.
DO
clean the saw after every use.
DO
always give a copy of this manual to the equipment user.
WARNINGS
RESULT IN DEATH OR SERIOUS BODILY INJURY.
DO NOT
Operate this saw unless you have read and understand
this operators manual.
DO NOT
Operate this saw without the blade guard, or other
protective guards in place
DO NOT
stand behind or in front of the blade path while the
engine is running.
DO NOT
leave this saw unattended while the engine is running.
DO NOT
operate this machine when you are tired or fatigued.
DO NOT
use abrasive blades that are less the 1/8" (3.17mm) thick.
DO NOT
exceed maximum blade speed shown for each blade size.
DO NOT
use damaged equipment or blades.
DO NOT
try to stop a moving blade with your hand.
DO NOT
use an abrasive blade that has been dropped.
DO NOT
not use Carbide tipped or toothed type blade of any kind.
DO NOT
use segmented diamond blades unless they are
specifically designed for high speed, hand-held saws.
DO NOT
place 1 inch (25.4mm) arbor hole blades on 20mm
flanges.
DO NOT
grind on the side of a cut-off blade.
DO NOT
cock, jam, or wedge the blade in the cut.
DO NOT
operate a cutting machine if the blade does not stop
rotating when the throttle trigger is released.
DO NOT
start cutting until you have a clear work area and secure
footing.
DO NOT
allow other people to be near the machine when starting,
refueling, or when the saw is operating.
DO NOT
operate the machine in the vicinity of anything that is
flammable. Sparks could cause a fire or an explosion.
DO NOT
allow bystanders or animals in the work area while using
a cut-off saw.
DO NOT
touch a dry cutting diamond blade immediately after use.
These blades require several minutes to cool after each
cut.
DO NOT
use damaged or worn blade flanges.
DO NOT
operate this machine in an enclosed area unless it is
properly ventilated.
DO NOT
allow blade exposure for the guard to be more than 180
degrees.
DO NOT
operate this saw without both hands on the handles.
..............................................................................................................................
This saw has been designed specifically for Fire Rescue cutting applications.
Do not modify or use this saw for any purpose other than Fire Rescue
cutting. If you have any questions relative to its intended application, do not
use the saw until you have been advised regarding an application in question.
3