Blue Angel BSE200 사용 설명서 및 부품 설명서 - 페이지 4

{카테고리_이름} Blue Angel BSE200에 대한 사용 설명서 및 부품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Blue Angel BSE200 4 페이지. Sewer ejector pump

페이지 인쇄

Operating Instructions And Parts Manual

Operation

2. With the cover uninstalled, add

water to the basin and observe the

float control switch operation.

Always disconnect the power

3. Also, test alarm switch if installed.

source before attempting to

4. Secure and seal basin cover.

install, service, relocate or

maintain the pump. Never touch sump

pump, pump motor, water or discharge

piping when pump is connected to

Do not run your pump in a dry sump.

electrical power. Never handle a pump

or pump motor with wet hands or when

standing on wet or damp surface or in

Do not attempt to oil the motor. A special

water. Fatal electrical shock could occur.

oil has been put in the motor housing at

1. Verify pump and switch operate

the factory. Use of any other oil could

damage the pump and WILL void the

within the basin.

warranty.

Maintenance

Risk of electrical shock! This pump is

supplied with a grounding conductor

and grounding type attachment plug.

Use a grounded receptacle to reduce

Always disconnect the electrical

the risk of fatal electrical shock.

supply before attempting to install,

service, relocate or perform any

Never cut off the round grounding

maintenance. If the power source is out

prong. Cutting the cord or plug will

of sight, lock and tag in the open (off)

void the warranty and make the pump

position to prevent unexpected power

inoperable.

application. Failure to do so could

result in fatal electrical shock. Only

qualified electricians should repair this

unit. Improper repair could result in

fatal electrical shock.

High Water Level

120º

Low Water Level

Figure 5 - Simplex System

www.blueangelpumps.com

1. Let the pump cool for a minimum of

two hours before servicing because

the pump contains hot oil under

pressure and the motor is hot.

2. Disassembly of the motor prior to

expiration of warranty will void the

warranty. If repairs are required,

see troubleshooting chart.

3. Inlet should be kept clean and free

of all foreign objects and inspect

annually. A clogged inlet will

damage pump.

4. Pump should be checked monthly

for proper operation.

This pump contains dielectric oil for

cooling. This oil can be harmful to the

environment. Check the state

environmental laws before disposing

this oil.

Pump #1

Pump #2

Discharge

On Level

Alarm Level

Off Level

Figure 6 - Duplex System

Operating Instructions And Parts Manual

Troubleshooting Chart

Symptom

Possible Cause(s)

Pump will not start or

1. Blown fuse

run

2. Low line voltage

3. Defective motor

4. Defective float switch

5. Impeller

6. Float obstructed

Pump starts and stops

1. Backflow of water from

too often

piping

2. Faulty float switch

Pump will not shut

1. Defective float switch

off or thermal

2. Obstacle in piping

protector turns off

3. Float obstructed

4. Low Line Voltage

5. Too many appliances on

circuit

Pump operates but

1. Plugged impeller

delivers little or no

2. Check valve installed

water

backwards

3. Pump airlocked

Corrective Action

1. If blown, replace with proper sized fuse or reset breaker

2. If voltage is under 108 volts, check wiring size

3. Replace pump

4. Replace float switch

5. If impeller will not turn, remove housing and remove

blockage

6. Make sure float(s) move freely up and down

1. Install or replace check valve

2. Replace float switch

1. Replace float switch

2. Remove pump and clean pump and piping

3. Make sure float move freely up and down

4. If voltage is under 108 volts, check wiring size

5. Install pump on dedicated circuit. IMPORTANT: Do not use

extension cord to power pump.

1. Clean out impeller

2. Reverse position of check valve

3. Check the 1/8" hole in discharge line between pump and

check valve; it should be 1" to 2" above discharge flange and

before the check valve