AKO Electronica AKO-14722 매뉴얼 - 페이지 2
{카테고리_이름} AKO Electronica AKO-14722에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AKO Electronica AKO-14722 2 페이지. Configurable electronic thermostats with 2 relays and up to 2 probes
페이지 인쇄1472H206
HOJA TÉCNICA
6 - DESCRIPTION OF PARAMETERS AND MESSAGES
The values in the Def column are factory-set.
Parameters
Functions and description
Temperature display
(0 = Whole in ºC) (1 = One decimal in ºC)
01
mode:
(2 = Whole in ºF) (3 = One decimal in ºF)
02 Probe 1, input S1
Enable?
03 Probe 1, input S1
Calibration (Offset)
04
Parameter 03 adjustable by the user?
05 Probe 2, input S2
Enable?
06 Probe 2, input S2
Calibration (Offset)
07
Parameter 06 adjustable by the user?
08 Thermostat relay R1,
Enable?
09 Thermostat relay R1,
Probe selection
10 Thermostat relay R1,
Operation type
11 Thermostat relay R1,
Set Point
12
Parameter 11 adjustable by the user?
13 Thermostat relay R1,
Differential (Hysteresis)
14
Parameter 13 adjustable by the user?
15 Thermostat relay R1,
Connection delay or protection
16
Parameter 15 adjustable by the user?
17 Thermostat relay R2,
Enable?
18 Thermostat relay R2,
Probe selection
19 Thermostat relay R2,
Operation type
20 Thermostat relay R2,
Set Point
21
Parameter 20 adjustable by the user?
22 Thermostat relay R2,
Differential (Hysteresis)
23
Parameter 22 adjustable by the user?
24 Thermostat relay R2,
Connection delay or protection
25
Parameter 24 adjustable by the user?
26 Timing relay R1,
Enable?
27 Timing relay R1,
Elapsed time between starts
28
Parameter 27 adjustable by the user?
29 Timing relay R1,
Duration
30
Parameter 29 adjustable by the user?
31 Timing relay R1,
Relay status during P29
32 Timing relay R2,
Enable?
33 Timing relay R2,
Elapsed time between starts
34
Parameter 33 adjustable by the user?
35 Timing relay R2,
Duration
36
Parameter 35 adjustable by the user?
37 Timing relay R2,
Relay status during P35
38 Parameters transfer
(0=disabled) (1=send) (2=receive)
39 Password to modify the configuration
40 Program version (information)
41 Display without pressing any key
42 Function by pressing UP key
43 Function by pressing UP key during 5"
44 Function by pressing DOWN key
45 Function by pressing DOWN key during 5"
Function by pressing UP + DOWN keys in panel mounting models
46
Function by pressing SET key in DIN rail models
The meaning for the options for parameters 41 to 46 is:
0=Key disabled
1=Display Probe 1 of input S1
2=Display Probe 2 of input S
3=R1 Set Point display
Messages
_ _ _
Permanent
Probe S1 and Probe S2 disabled.
Probe S1 damaged (open, crossed circuit, temp. > 110ºC or
E1
Permanent
temp. <-55ºC). Assigned relay OFF.
Probe S2 damaged (open, crossed circuit, temp. > 110ºC or
E2
Permanent
temp.<-55ºC). Assigned relay OFF.
Probes S1+S2 damaged (open, crossed circuit, temp. > 110ºC or
E1+E2 Flashing
temp. <-55ºC). Relays R1 and R2 OFF.
EE
Permanent
Memory error
REMARK: When the time parameters are modified, the new values are applied once the current
cycle is completed. In order for it to have an immediate effect, switch the controller off and then
on again.
351472206 REV. 00 2003
D.L.: B-33.359-03
Edición 01
Values
Min.
Def.
0
1
0=No 1=Yes 1=Yes
(ºC/ºF) -20,0
0,0
0=No 0=No 1=Yes
0=No 1=Yes 1=Yes
(ºC/ºF) -20,0
0,0
0=No 0=No 1=Yes
0=No 1=Yes 1=Yes
(0=S1- S2) (1=S1) (2=S2)
0
1
(0=Cold) (1=Heat)
0
1
(ºC/ºF) -50,0
0,0
0=No 1=Yes 1=Yes
(ºC/ºF) -90,0
1,0
0=No 1=Yes 1=Yes
(min)
0
0
0=No 1=Yes 1=Yes
0=No 1=Sí 1=Yes
(0=S1- S2) (1=S1) (2=S2)
0
2
(0=Cold) (1=Heat)
0
1
(ºC/ºF) -50,0
0,0
0=No 1=Yes 1=Yes
(ºC/ºF) -90,0
1,0
0=No 1=Yes 1=Yes
(min)
0
0
0=No 1=Yes 1=Yes
0=No 0=No 1=Yes
(h)
0
0
0=No 1=Yes 1=Yes
(min)
0
0
0=No 1=Yes 1=Yes
(0=OFF) (1=ON)
0
0
0=No 0=No 1=Yes
(h)
0
0
0=No 1=Yes 1=Yes
(min)
0
0
0=No 1=Yes 1=Yes
(0=OFF) (1=ON)
0
0
0
0
0
0
1
1
0
2
0
4
0
0
0
3
0
7
4=R2 Set Point display
5=Start R1 timing
6=Start R2 timing
7=Accessible parameters adjustment
7 - RELAYS R1 AND R2 OPERATION AND CONTROL
Thermostat relay R1
P11=Parameter 11, Set Point
Operation for HEAT (P10=1)
Max.
3
ON
P13
20,0
OFF
P11
Start
20,0
<
P13
0
ON
2
1
OFF
99,0
P11-P13
P11
Start
Stop
90,0
Operation for COLD (P10=0)
120
2
ON
P13
1
99,0
OFF
P11
Stop
90,0
120
<
P13
0
ON
120
OFF
P11-P13
P11
Stop
Start
120
1
8 - PARAMETERS TRANSFER
120
AKO-14916
Tabletop server which is connected by
means of the AKO-80018, 230/12V, to the
power supply. Permit to transfer parameters
120
previously
recorded
in
AKO-14918, to other panel mounting con-
trollers without these having to be powered.
1
2
Supply 230V
126
AKO-80018
4
AKO-14916
7
7
7
7
7
Transfer
Panel mounting models
9 - MAINTENANCE
Clean the unit surface with a soft cloth and soap and water. Do not use abrasive detergents,
petrol, alcohol or solvents.
10 - WARNINGS
The use of the unit different to the manufacturer's instructions voids the safety qualification.
To ensure correct operation of the apparatus, only NTC type probes supplied by AKO should
be used.
Between -40 ºC and +20 ºC, when the probe is extended up to 1.000m with minimum 0,5mm
cable, deviation will be less than 0.25 ºC (probe extension cable ref. AKO-15586).
( 02 de 02 )
www.ako.com
Thermostat relay R2
P20=Parameter 20, Set Point
Operation for HEAT (P19=1)
>
0
ON
OFF
P11+P13
TEMP.
Stop
P22
ON
OFF
TEMP.
P20-P22
Start
Operation for COLD (P19=0)
>
0
ON
OFF
P11+P13
TEMP.
Start
P20
ON
OFF
TEMP.
P20-P22
Stop
AKO-14918
A portable server without supply to which
the parameters programmed in powered
AKO controllers can be copied. The para-
one
server
meters may then be transferred from the ser-
ver to other identical powered units.
AKO-14918
AKO-14918
Transfer
Power supply
Programming
Panel mounting or DIN rail models
>
P22
0
P20
P20+P22
TEMP.
Start
Stop
<
0
P20
TEMP.
Stop
>
P22
0
P20
P20+P22
TEMP.
Stop
Start
<
0
P20
TEMP.
Start
AKO-14918
Transfer
Power supply
ºC
ºF
SET
Programming
2