Dobinsons BU45-3691 설치 매뉴얼 - 페이지 4

{카테고리_이름} Dobinsons BU45-3691에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dobinsons BU45-3691 8 페이지. Bullbar nissan patrol gu series 4 on

페이지 인쇄

Fitting Guide

1. Remove the number plate.

2. Remove the bumper bar or factory bullbar if

fitted.

3. Install the bullbar mounting brackets and

cross brace as per the diagram on page 3.

4. Install all bolts and tighten. The bolts at the

top rear section of the outer brackets may

need to be drilled through the chassis and

installed.

5. Carefully un-wrap the bulbar taking care not

to scratch it especially on the top loops.

Reinstall the number plate to the bullbar as it

is easier now. If installing driving lights to the

bullbar it is easiest to install now.

6. If mounting a winch see steps 7 – 16.

7. The winch mounts directly to the rear of the

bullbar. If fitting a Dobinsons Winch the

clutch handle will be on the left hand side of

the vehicle, with the wire spooling from the

bottom of the winch.

8. See the Installation section of your Dobinsons

4x4 Winch manual for specific detailed fitting

instructions. For a brief overview see the

following steps.

9. This will require the clutch handle and gear-

box housing to be rotated forward 2 bolt

holes to allow easy access through the bulbar

holes. See instructions in winch user manual.

10. Determine where the winch control box will

be located and mount the control box; it is

easiest to mount to the top of the bar.

11. Sit the winch behind the bullbar and un wind

about a metre of cable and pass through the

fairlead hole in the bullbar.

12. With the fairlead sitting in front of the bullbar

pass the winch cable through the roller

fairlead. This may require removing a circlip

from the fairlead and re installing once the

cable is passed through.

13. With help from another person, hold the

fairlead in position at the front of the bullbar

and the winch in position at the rear of the

bullbar and bolt the winch and fairlead to the

bullbar using the lower bolts.

Dobinsons Springs and Suspension

14. Install the top winch mounting bolts.

15. Tighten the winch bolts and ensure the winch

bolts are not too long and tighten correctly.

16. Wire the winch up as per the winch

instruction manual and bolt the winch to the

mounting bracket. Route the wires and

connect to battery and also route the

breather hose.

17. Wire up the lights. Using a multimeter or test

light first locate the earth wire, parker positive

and indicator positive wires from the wiring

on the back of the original vehicle lights on

each side.

18. Unclip the wiring from the indicator/parker

lights. Check that the wiring will be long

enough to reach the new bullbar

indicator/parker lights and extend if required.

Using the diagram at the end of this manual,

join the corresponding wires to original

vehicle wires located in the previous step. The

wires can be joined by either using good

quality snap lock crimp connectors or by

soldering. Ensure the connection is secure and

is sufficiently insulated.

19. If fitting a bullbar with fog lights, the fog lights

can be connected using the original vehicle

fog light wires if fitted. If required, cut the old

fog light wiring plugs off and cut the new fog

light wiring plugs and join. If the vehicle is not

fitted with OEM fog lights the wiring loom

supplied can be used. Follow the wiring

diagram at the end of this manual.

20. For a better finish the lower outer sections of

the front wheel arch panel can be painted

satin black.

21. With help, fit the bulbar into position and

install nuts and bolts supplied. The

adjustment stopper bolts on the front of the

bullbar (item 3) touch against the front of the

chassis. Depending on the exact alignment of

the bar these may need to be cut a little

shorter.