Fleck 5600 Econominder 설치 지침 매뉴얼 - 페이지 6
{카테고리_이름} Fleck 5600 Econominder에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Fleck 5600 Econominder 19 페이지.
Fleck 5600 Econominder에 대해서도 마찬가지입니다: 소유자 매뉴얼 (8 페이지), 설치 매뉴얼 (11 페이지)
페이지 인쇄
S S t t a a n n d d a a r r d d
1 1 6 6 k k
C C a a p p a a c c i i t t y y
T T a a n n k k ( ( i i n n
8 x 44
i i n n c c h h e e s s ) )
G G r r a a v v e e l l
10 lb
R R e e s s i i n n
0.5 ft³
On systems shipped by truck the resin may be preloaded
B B e e f f o o r r e e y y o o u u s s t t a a r r t t p p l l u u m m b b i i n n g g
2 2 — — P P
- -
R R E E
I I N N S S T T A A L L L L A A T T I I O O N N P P R R E E P P E E R R A A T T I I O O N N
* * * * M M o o n n e e y y - - s s a a v v i i n n g g t t i i p p : : * * * *
preparing the tank ahead of time. This cuts down on the time the plumber has to spend and doing so is
simple enough that most people can accomplish it in less than an hour.
2 2 . . 1 1 — — V V e e r r i i f f y y r r i i s s e e r r t t u u b b e e s s i i z z i i n n g g
IIm mg g 1 1 -- T Ta an nk k & & R Riis se er r
2 2 . . 2 2 — — F F i i l l l l t t a a n n k k p p a a r r t t i i a a l l l l y y w w i i t t h h w w a a t t e e r r
This optional step will help buffer the resin as it is poured in and will also help minimize air bubbles
upon initial startup. Simply pour water into the tank until it is 1/4 - 1/3 filled with water.
2 2 . . 3 3 — — L L o o a a d d r r e e s s i i n n a a n n d d g g r r a a v v e e l l — —
T T a a n n k k S S i i z z e e a a n n d d R R e e s s i i n n Q Q t t y y
2 2 4 4 k k
3 3 2 2 k k
8 x 44
9 x 48
10 lb
12 lb
0.75 ft³
1 ft³
If hiring a plumber to do the installation you can save some money by
* * ! ! * * V V e e r r i i f f y y t t h h e e r r i i s s e e r r t t u u b b e e fi fit t s s a a n n d d s s e e a a l l s s i i n n t t o o t t h h e e c c o o n n t t r r o o l l h h e e a a d d . . * * ! ! * *
A mismatched riser tube will prevent proper treatment, and it is
much easier to correct the problem before the resin is loaded. The
riser tube sits in an indentation centered in the bottom of the tank.
With the riser tube properly positioned, ensure that it is within 1/3
inch (8 mm) above or below the lip of the tank. If it is not contact us
for help correcting the problem.
* * * * O O p p t t i i o o n n a a l l * * * *
* * ! ! * * g g r r a a v v e e l l g g o o e e s s i i n n fi fir r s s t t * * ! ! * *
4 4 8 8 k k
6 6 4 4 k k
12 x 48
10 x 54
OR 12 x
52
16 lb
20 lb
1.5 ft³
2 ft³
6 of 19
8 8 0 0 k k
9 9 6 6 k k
13 x 54
14 x 65
35 lb
50 lb
2.5 ft³
3 ft³
1 1 1 1 0 0 k k
14 x 65
50 lb
3.5 ft³
.