Dodge Imperial 사용 설명서

{카테고리_이름} Dodge Imperial에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Dodge Imperial 2 페이지. Bearing

These instructions must be read thoroughly before installation or operation. This instruction manual was accurate at the time of

printing. Please see dodgeindustrial.com for updated instruction manuals.

WARNING: To ensure the drive is not unexpectedly started, turn off and

lock-out or tag power source before proceeding. Failure to observe these

precautions could result in bodily injury.

INSPECTION

Inspect shaft to ensure it is smooth, straight, clean and within

commercial tolerances.

MOUNTING

Install the Non-Expansion Unit First

Remove lock plate located on the face of the locknut.

Turn locknut counterclockwise until bearing will freely slide

onto the shaft.

Slide bearing to the desired position on the shaft.

NOTE: All weight must be removed from the bearing

when obtaining the zero reference point.

The zero reference point is defined as the point when the

clearance between the adapter sleeve, shaft, and bearing

bore has been removed.

To reach the zero reference point, rotate locknut clockwise

using both hands as tightly as possible. When mounting

bearing with shaft sizes 3-15/16" and larger, the following test

WARNING: Because of the possible danger to person(s) or property

from accidents which may result from the improper use of products,

it is important that correct procedures be followed. Products must be

used in accordance with the engineering information specified in the

catalog. Proper installation, maintenance and operation procedures

must be observed. The instructions in the instruction manuals must

be followed. Inspections should be made as necessary to assure

safe operation under prevailing conditions. Proper guards and other

suitable safety devices or procedures as may be desirable or as may

be specified in safety codes should be provided, and are neither

provided by Dodge

nor are the responsibility of Dodge. This unit and

its associated equipment must be installed, adjusted and maintained

by qualified personnel who are familiar with the construction and

operation of all equipment in the system and the potential hazards

involved. When risk to persons or property may be involved, a holding

device must be an integral part of the driven equipment beyond the

speed reducer output shaft.

Imperial & ISAF Bearing

Instruction Manual

Locknut

Lock Plate

Adapter Sleeve

Figure 1

WARNING: All products over 25 kg (55 lbs) are noted on the shipping

package. Proper lifting practices are required for these products.

must be performed. As a test to ensure you have reached the

zero reference point, tap on the O.D. of the nut with a hammer

and attempt to rotate the nut using both hands. If the nut will

not rotate then you have reached zero reference point and

you should proceed to step 5. If you can rotate the nut using

both hands, you have not reached the true zero reference

point and you should repeat step 4a until zero reference point

is obtained. When the zero reference point is reached, the

bearing will not be able to move by hand axially on the shaft.

Scribe a line through the locknut face and adapter face.

Using a spanner or drift and hammer, rotate locknut clockwise

by the number of turns shown in Table 1.

Dismount

Table 1–Locknut Rotation from "Zero Reference Point"

Shaft Size (inches)

1-1/8 - 1 7/16

* 1-1/2

** 1-1/2

1-5/8 - 2

2-3/16 - 3

3-3/16 - 4

4-7/16 - 4 1/2

4-15/16 - 5 1/2

5-15/16 - 6

6-7/16 - 7

* IMPERIAL IP & ISAF

** IMPERIAL IP With Type E Dimensioned Housing

Scribe Line

Figure 2

Mount

Figure 3

Locknut Rotation

3/4 to 7/8 turn

7/8 to 1 turn

1 to 1-1/4 turns

1-1/4 to 1-1/2 turns

1-1/8 to 1-3/8 turns

1-3/8 to 1-5/8 turns

1 to 1-1/4 turns

1-1/8 to 1-3/8 turns