3M 6503 사용자 지침 - 페이지 4

{카테고리_이름} 3M 6503에 대한 사용자 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. 3M 6503 5 페이지. Rugged comfort half facepiece reusable respirator

페이지 인쇄

NIOSH Approvals

P100

P95

N95

Nuisance level relief***

Acid gases

Organic Vapors

** 3M recommended for ozone protection up to 10 times the OSHA PEL or applicable government

occupational exposure limits, whichever is lower.

NOTE: Not NIOSH approved for use against ozone.

*** 3M recommended for relief against nuisance levels of acid gas or organic vapors. Nuisance level refers

to concentrations not exceeding OSHA PEL or applicable exposure limits, whichever is lower. Do not use for

respiratory protection against acid gas/organic vapors.

In Brazil, the 5935BR fi lter is approved as a NIOSH N95 fi lter and as a BMOL P3 fi lter.

3M™ Filter Adapters and Retainers

Number

Description

501

Filter Retainer for use with Cartridge 6000 Series and Filters 5N11 and 5P71

502

Filter Adapter for use with Cartridge 6000 Series and Filters 2000 and 7093/7093C

603

Filter Adapter for use with Filters 5N11 and 5P71

In Brazil, the 5935BR fi lter can be used with the 3M™ Filter Adaptor 603 and the 3M™ Filter Retainer

501 on the 3M

Rugged Comfort Half Facepiece Reusable Respirator, 6500 Series.

Service Life of Chemical Cartridges and Particulate Filters

Failure to properly dispose of spent cartridges or fi lters, or respirators contaminated by hazardous

materials can result in personal exposures as well as environmental harm. Handling, transportation and

disposal of spent cartridges, fi lters, or respirators must comply with all applicable federal, state, provincial

and local laws and regulations.

3M™ Chemical Cartridges 6000 Series must be used before the expiration date on cartridge packaging.

The useful service life of these cartridges will depend upon the activity of wearer (breathing rate), specifi c

type, volatility and concentration of contaminants and environmental conditions such as humidity, pressure,

and temperature. Cartridges must be replaced in accordance with an end of service life indicator (ESLI),

established change schedule, regulations or earlier if smell, taste or irritation from contaminants is detected.

Particulate fi lters must be replaced if they become damaged, soiled or if increased breathing resistance

occurs. N-series fi lters should not be used in environments containing oils. R-series fi lters may be limited

to 8 hours of continuous or intermittent use if oil aerosols are present. In environments containing only oil

aerosols, P-series fi lters should be replaced after 40 hours of use or 30 days, whichever is fi rst.

Replacement Parts Instructions

3M™ Rugged Comfort Half Facepiece Reusable Respirator Assembly 6500

The facepiece assembly consists of the head harness assembly and valve cover, exhalation valve, and

inhalation valves.

3M™ Head Harness Assembly & Valve Cover Replacement

1. Remove Head Harness Assembly & Valve Cover by placing thumb beneath valve cover and fi ngers at the

top. Pull the valve cover bottom away from facepiece with the thumb and then up to release the valve

cover (Fig. 22).

2. Replace Head Harness Assembly & Valve Cover by positioning the peg on the facepiece into the notch at

the top of the valve cover. Press the bottom of the valve cover into the facepiece. When properly engaged,

an audible snap should be heard.

Exhalation Valve Replacement

1. Remove 3M™ Head Harness Assembly & Valve Cover 6581 by pulling away from faceseal (Fig. 22).

2. Remove 3M™ Exhalation Valve 6583 from valve seat by grasping the valve and pulling each valve stem

out from the valve seat (Fig. 23).

Inspect valve seat, making certain it is clean and in good condition.

Replace 3M™ Exhalation Valve 6583 by inserting stems into the two holes until they are visible from

inside the facepiece and then pulling the stems through until they are seated and secured (Fig. 24).

5. Replace 3M™ Head Harness Assembly & Valve Cover 6581 by positioning the peg on the facepiece

into the notch at the top of the valve cover. Press the bottom of the valve cover into the facepiece. When

properly engaged, an audible snap should be heard.

NOTE: Conduct a negative pressure user seal check to ensure exhalation valve is functioning properly.

Inhalation Valve Replacement

Inhalation valves are located on the inside of the facepiece inhalation ports. These valves should be inspected

before each respirator use and during cleaning. Replace whenever valves become damaged or lost.

1. Remove existing valve(s) by grasping valve and pulling valve off the center post.

2. Replace valve(s) by pressing the hole of the valve over the center post on the valve seat (Fig. 25). Be

certain valve(s) is fully engaged through valve post(s) and lays fl at.

3M™ Filters

X X X

W CAUTION

3M™ Rugged Comfort Half Facepiece Reusable Respirator, 6500 Series

Replacement Parts & Accessories

Number

Description

6501

Small

6502

Medium

6503

Large

Number

6581

6583

6893

Number

504

601

For Compliance in Brazil and elsewhere, NOTE:

1. Do not use in defi cient or enriched oxygen atmospheres.

2. Storage, Transportation and Care: store in a clean and dry place and away from contaminants and

extreme temperature and humidity.

3. The components of this respirator are made of materials which are not expected to cause adverse

health effects.

4. It is necessary to have special care to use this product in explosives atmospheres.

Product Manufacturing Date

The parts of the product show markings that bring information of manufacturing date, and its reading is

described as in the example below:

7 6 5

Date Code = 12

month 1999 (12/99)

Description

Head Harness

Assembly

Exhalation Valve

Inhalation Valve

6581

Fig. 26

Description

Respirator Cleaning Wipes

Quantitative Fit Test Adapter

6893

6583