Cygnet U36A1D 지침 - 페이지 2

{카테고리_이름} Cygnet U36A1D에 대한 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Cygnet U36A1D 2 페이지. Electric catering urn

페이지 인쇄

CP149435MUK-62091Rev5-Cygnet:8749 Burco boilers 4pp

Important

•

This appliance is not suitable for

installation in an area where a

safeguards

water jet could be used.

•

This appliance must not be

cleaned by a water jet.

•

To avoid being scalded when the

•

This appliance is only to be

urn is operating or has just been

installed in locations where its use

switched off keep hands away

and maintenance is restricted to

from any steam from the lid. Be

trained personnel.

particularly careful not to touch

•

For correct operation this

hot surfaces when opening the lid

appliance should be operated in

or filling.

an ambient temperature between

•

Do not use the appliance if it has

22-28 °C.

malfunctioned or has been

damaged in any way.

Installation

•

Do not dismantle any part of the

urn. Responsibility cannot be

accepted if this instruction is

Preparation

ignored.

•

Do not place the urn on or near

hot surfaces.

•

Do not use accessories or

Remove any plastic film from the

attachments which are not

urn and wipe over all surfaces with

recommended or sold by Burco

a damp cloth.

Appliances as they can cause

Check that the voltage shown on

hazards.

the rating plate is suitable for your

•

This appliance must only be used

supply.

for heating water.

Before general use it is

•

Always switch off and disconnect

recommended that the urn is

the urn from the mains supply

boiled twice discarding the water

when not in use or when cleaning.

each time.

•

To prevent any risk of

electrocution do not immerse the

Fitting a plug

urn in water or any other liquid

when cleaning and do not allow

any water or liquid to come into

The mains lead of this urn will

contact with any of the electrical

already be fitted with a BS1363 13A

connections or controls.

plug. In the event of replacing a fuse,

•

Do not allow the cord to hang

a 13 amp fuse approved by ASTA or

over the edge of the work surface,

BSI must be used.

to touch wet or hot surfaces or

If the plug is not suitable for your

become twisted.

socket then the plug must be cut off

•

The urn should not be lifted whilst

and disposed of safely.

connected to the mains.

An appropriate plug should be

•

The urn should not be carried

fitted as follows:

whilst it contains water.

IMPORTANT: The wires in the

•

Maintenance other than cleaning

mains lead are coloured in accordance

should be performed by the

with the following code:

manufacturer while this product is

Green-and-Yellow – Earth

within guarantee (contact our

Blue – Neutral

service help line) or otherwise by a

Brown – Live

qualified service engineer.

The wire, which is coloured green-

•

This appliance is not suitable for

and-yellow, must be connected to the

installations in an area where a

terminal in the plug which is marked

water jet could be used.

with the letter E or the earth symbol

•

This appliance is not to be

or coloured green or green-and-

intended for use by persons

yellow.

(including children) with reduced

The wire, which is coloured blue,

physical, sensory or mental

must be connected to the terminal

capabilities or lack of experience

which is marked with the letter N or

and knowledge unless they have

coloured black or blue.

been given supervision or

The wire, which is coloured brown,

instruction concerning use of the

must be connected to the terminal

appliance by a person responsible

which is marked with the letter L or

for their safety. Children should be

coloured red or brown.

supervised to ensure that they do

Make sure that the connections

not play with the appliance.

are tight and that there are no loose

strands of wire and no insulation

15/10/08

10:37

Page 4

trapped under the terminals. Tighten

knob to approximately one of the

the clamp in the plug making sure that

following positions:

it grips the outer covering of the cord.

In a 13A (BS 1363) fused plug, fit a

13A fuse. Tighten the plug cover

securely.

If you are in any doubt, consult a

qualified electrician.

IMPORTANT: If the supply cord is

damaged, it must be replaced by the

at an exact temperature, use a

manufacturer, service agent or similar

thermometer to check this. Stir the

qualified person in order to avoid a

water before taking the temperature

hazard. The supply cord may become

and when the desired temperature has

warm when the appliance is in use.

been reached, turn the control knob

WARNING: This appliance

slowly to the left until a click from the

must be earthed.

thermostat is heard. The thermostat

will cycle on and off to maintain the

Location

temperature.

Serving

•

More than 100mm from any wall.

•

On a flat level surface.

•

This appliance is for indoor use

only.

Using

IMPORTANT: Always put water in

the urn before switching on.

Lift the lid and fill the urn with the

desired amount of water.

•

Do not fill above the 'MAX'

capacity mark.

WARNING

If the urn is over

filled there is a risk that boiling water

may be ejected.

•

Under filling will cause the boil dry

cut-out to operate (and may

shorten the life of the element).

The urn is not suitable for boiling

After use

liquids other than water or for boiling

water containing small solid particles.

If the water is being boiled for tea

making, it is best to make the tea in

another container. However, if it is

necessary to make the tea in the urn it

should be suspended clear of the urn

it is not in use for short periods, but to

bottom and heating elements in a

maintain a supply of fresh water, it

muslin bag. If it is intended to boil

should be emptied periodically and

large items such as puddings or hams

cleaned out.

in the urn, they should be suspended

clear of the urn bottom and heating

disconnected and empty.

element.

Protective cut-out

Thermostat control

The green light will glow to show

a thermal cut-out which protects the

power is connected to the urn.

urn from damage if it is allowed to boil

Turn the control knob to 6.

dry or is switched on without water. If

When the water boils, turn the

this happens, allow the urn to cool

control knob to approximately

down then press the reset button

setting 5 to keep it simmering. An

situated under the base. If this

exact setting will be found by

happens, allow the urn to cool, drain

experience.

the water then press the reset button,

To maintain the water at any

situated on the base.

other temperature, set the control

Guarantee registration

Approx temp

Knob setting

37ºC (99ºF)

55ºC (131ºF)

Appliance model

68ºC (155ºF)

82ºC (180ºF)

100ºC (212ºF)

5/6

If it is necessary to keep the water

Serial no.

Date of purchase

Customer name

Address

Safety tap

The tap is locked or

unlocked by twisting it so that the

closed or opened padlock symbol

is lined up with the white dot on

the tap body.

General operation

There are

two open positions, one self-

holding so that the tap remains

open, and the other self-closing so

that the tap closes as soon as the

lever is released. To change the

tap position, turn the tap lever

Please help us to further improve our products by ticking the one

through 180º.

Open the tap by depressing the

main reason for purchase

tap lever into the horizontal

position.

Close the tap by returning the

lever to a vertical position.

Switch off to 0 and disconnect

from the mains supply.

Water may be left in the urn when

Dealer recommendation

Other (please state)

WARNING:

Only move when

Where did you buy your Burco appliance ?

Dealer/Retailer

The heating element is fitted with

Would you like more information on Burco products?

If you would like to receive information on new BURCO products

please supply your email address below:

In order to ensure correct

I I

Price

Styling/Appearance

I I

Features

Previous Burco ownership

I I

Service back-up

I I

Yes