Doheny's 5166 설치, 운영 및 부품 - 페이지 2

{카테고리_이름} Doheny's 5166에 대한 설치, 운영 및 부품을 온라인으로 검색하거나 PDF를 다운로드하세요. Doheny's 5166 4 페이지. Cartridge filters

페이지 인쇄

CHAPTER 1

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

1. The installation should be carried out in accordance

to the safety instructions of swimming pools and

the specific instructions for each facility.

2. The user should make sure that the installation is

carried out by qualified authorized persons and that

these persons have first carefully read the following

instructions. Incorrectly installed equipment may

fail, causing sever injury or property damage.

3. The operating safety of the filter is only guaranteed if

the installation and operation instructions are

correctly followed.

4. To reduce the risk of injury, do not permit children

to use this product.

5. Chemical spills and fumes can weaken Swimming

Pool or Spa. Corrosion can cause filters and other

equipment to fail, resulting in severe injury or

property damage. Do not store pool chemicals near

your equipment.

6. Any modification of the filter is not authorized. The

supplier assumes no liability for the damage and

injuries caused by unauthorized replacement parts

and accessories.

CHAPTER 2

: INSTALLATION INSTRUCTIONS

▲WARNING This product should be installed and

serviced only by a qualified professional.

It is important to first determine where your pump and

filter will be located. If above the water line, a self-

priming pump must be used. Self-priming pumps have

the ability to lift water from a lower level and prime

automatically.

1. Position the filter next to the Swimming Pool or Spa.

2. The filter should be placed on a level concrete

slab, very firm ground, or equivalent. Ensure that

the ground will not subside, preventing any strain

from the attached plumbing.

3. Position the filter so that the piping connections,

Multi-Port Valve and winter drain is convenient and

accessible for operation, servicing and winterizing.

4. Ensure that the compliance label is facing the

front to allow easy identification in the case of

service difficulties.

5. If practical, place pump and filter in the shade to

shield it from continuous direct heat from the sun.

10411 80th Avenue Pleasant Prairie, WI 53158 | Orders and Customer Care: 1-800-574-7665 | Fax: 1-800-323-5932 | Doheny.com

Plumbing

1. Use 1-1/2 inch or 2 inch piping. When making

permanent connections, be sure to provide unions

for easy servicing.

2. Refer to the diagrams for basic suggested valving.

Ball valves are recommended where needed. While

all systems vary, the main consideration is to provide

the desired control of water flow from the pool to the

pump and filter, and back to the pool. When the filter

is located below water level, provide valves to

prevent back flow of water to the filter during cleaning

and routine servicing.

3. All plumbing on these cartridge filters are 1-1/2 inch or

2 inch Male and Female National Pipe Threading

(NPT). Use plastic adapters when making threaded

connections to the filter. Take the Teflon tape and

wrap the male threads three times in a clockwise

direction. Screw the male adapter into the female

adapter with your hand till its tight. Don't tighten too

tight as the adapters are plastic and can break.

4. Connect the pool suction plumbing between the

skimmer, pool outlet, and the pump.

5. Install the pool return plumbing.

6. If pressure gauge is not installed, apply the Teflon

tape to the gauge threads (just like you did to the

male adapter) and carefully screw the threaded hole

into the filter head.

7. A filter drain is furnished with each filter and is

needed for complete filter draining. A manual air

relief valve is furnished to aid in bleeding off unwanted

when starting the filter. The auto air relief valve

provides air removal during operation.

8. All electrical connections should be made in

accordance with local codes and done by a qualified

authorized person.

9. Check for joint leaks before operating.

10. Refer to pump manual for pump information.

Starting the Filter

1. Make sure filter drain is closed. Open the manual air

relief valve by turning it counter-clockwise a few

times and open the suction and return valves.

▲CAUTION All suction and discharge valves must

be open when starting the system. Failure to do so

could cause severe personal injury and/or property

damage. Make sure locking ring is secure (hand

tighten, only slight pressure is required).

2. Stand clear of the filter, prime and start the pump,

following the manufacturer's pump manual.

3. Air trapped in the system will automatically vent to

the pool and out the air relief valve. Close air relief

valve as soon as air is vented by turning the valve

counter-clockwise.