3M Adflo 35-3099-01 매뉴얼 - 페이지 4

{카테고리_이름} 3M Adflo 35-3099-01에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. 3M Adflo 35-3099-01 7 페이지. Powered air purifying respirator (papr) assembly
3M Adflo 35-3099-01에 대해서도 마찬가지입니다: 사용자 지침 (2 페이지)

페이지 인쇄

35-0699-99X01

Nuisance Odor Pad Assembly, 1/Case

35-0799-99X01

Nuisance Odor Pad, 1/case

35-0799-99X10

Nuisance Odor Pad, 10/case

15-0399-99X02

Organic Vapor/Acid Gas* Cartridge, 2/case

15-0399-99X06

Organic Vapor/Acid Gas* Cartridge, 6/case

15-0499-99X02

Organic Vapor/Acid Gas* Cartridge, 2/case

15-0499-99X06

Organic Vapor/Acid Gas* Cartridge, 6/case

15-0009-99X02

Spark Arrestor, 2/case

* Acid gas: NIOSH approved for sulfur dioxide, chlorine, hydrogen chloride

TROUBLESHOOTING

Use the table below to help identify possible causes and corrective action for problems you may experience. There are no

user serviceable parts inside the 3M™ Adflo™ PAPR Assembly. The motor/blower unit should not be opened to attempt

repairs. Consult the 3M™ Adflo™ PAPR Trouble Shooting Guide or contact 3M Technical Service to help identify additional

possible causes and corrective actions for other problems you may experience.

Fault

Probable Cause(s)

Low air flow alarm (audible

1. Breathing tube is blocked.

and all three LEDs on

2. Filter is blocked.

power button are lit)

3. Filter is fully loaded with

particles.

4. PAPR is being used above

recommended altitude

limitation.

Bottom bar of battery

Low battery voltage.

indicator flashes; battery

alarm sounds

No air flow, no alarm(s)

1. Battery contact on battery

pack is damaged.

2. Battery is completely

discharged.

3. Damaged circuit board.

4. Damaged motor.

Low air flow per indicator

1. Damaged circuit board.

but no alarm(s)

2. Damaged motor.

User detects odor or taste

1. Incorrect respirator

of contaminants or feels

for application and/or

eye or throat irritation

environment.

2. Chemical cartridge exhausted.

3. Nuisance odor pad.

4. Particle filter damaged.

Battery pack's charge lasts

1. Inadequate charging.

less than expected

2. HE filter is loaded with

particles, making the motor

run harder.

3. Chemical cartridge being

used.

4. Motor blower is being used at

high elevations.

The motor runs "faster than

1. The HE filter is loaded with

normal"

particles.

2. Recent user change from just

HE filter to HE and Nuisance

Odor Pad Assembly or HE and

OV/AG cartridge.

The motor runs "slower

1. Recent user change from

than normal"

HE and Nuisance Odor Pad

Assembly or HE filter and

OV/SD/CL/HC cartridge to just

the HE filter.

Possible Solution(s)

1. Check & remove blockage or obstruction.

2. Check air filter & remove obstruction.

3. Change HE filter and pre-filter. If using a

chemical cartridge, check that the scrim

fabric behind the inlet holes is clean and

white. Any sign of particle loading on the

chemical cartridge indicates improper

installation or damaged particle filter

assembly.

4. Consider 3M™ High Altitude Compensation

Adflo™ PAPR or an alternative 3M™ PAPR.

1. Fully charge the battery pack.

2. Install a new, fully-charged 3M™ Adflo™

PAPR Battery Pack.

1. Check that the battery contact is not bent or

broken.

2. Fully charge the battery pack.

3 and 4. Contact 3M Warranty and Repair.

Contact 3M Warranty and Repair.

1. Consult on-site industrial hygienist or safety

director.

2. Change cartridge & develop a cartridge

replacement schedule with your on-site

industrial hygienist or safety director.

3. Replace nuisance odor pad.

4. Replace particle filter.

1. Check the filter-loading indicator.

2. Replace the HE filter & pre-filter as indicated,

and examine the spark arrestor.

3. Battery pack will normally have shorter run

time with chemical cartridge in place.

4. Consider 3M™ High Altitude Compensation

Adflo™ PAPR or an alternative 3M™ PAPR.

1. Check the filter-loading indicator. Replace

the HE filter & pre-filter as indicated, and

examine the spark arrestor.

2. Normal operation. Let the unit run for 2

minutes so it can automatically adjust to new

configuration.

1. Normal operation. Let the unit run for 2

minutes so it can automatically adjust to the

new filter configuration.

Fig. 2

Fig. 1

1- Cover; 2 - Spark Arrestor; 3-Pre-filter; 4 - HE Filter

1- Protège-filtre; 2- Pare-étincelles; 3- Préfiltre;

4- Filtre à haute efficacité

Fig. 4

Fig. 5

Fig. 7

Fig. 8

Fig. 9A

Fig. 10

Fig. 13

Fig. 12

Fig. 3

Fig. 6

Fig. 9

Fig. 11

Fig. 14