Ashford Katie Table Loom 지침 - 페이지 3
{카테고리_이름} Ashford Katie Table Loom에 대한 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Ashford Katie Table Loom 3 페이지. A folding 8 shaft 30cm (12ins) table loom
Ashford Katie Table Loom에 대해서도 마찬가지입니다: 지침 (3 페이지)
페이지 인쇄
Project notes for the Katie Table Loom
Please read in conjunction with the Learn to Weave on the Table Loom booklet.
YOUR FIRST PROJECT – TABLE RUNNER
You will need:
Warping frame
Ruler or yarn gauge
Tape measure
Raddle
String
Scrap yarn
Scissors
Warp and weft yarn – Ashford Cotton 5/2 (100% cotton;
848m/927yds; 200gms/7oz), Bleached White 300gm (101/2oz),
Twilight Grey 60gm (2.1oz) and Black 110gm (3.8oz).
Here's how:
Sett – 20 ends per inch (8 ends per cm)
No. of ends: 240
Warp length: 2yds (2m)
Width in reed: 12ins (30cm)
Finished size (hemmed and washed): 9¾ x 46in (25 x 116cm)
Weave Structure:
Twill
Reading the Draft for the Table Runner
Pattern drafts are made of four parts:
1. Threading draft
2. Shafts
3. Liftings
4. Drawdown
1. Threading Draft
This shows the order in which the warp is threaded through the heddle
eyes. Threading drafts are read from right to left. For this project, the
first warp thread will be threaded through the heddle on shaft one. Two
pattern repeats are shown. The bracket below shows how many times
to repeat each section.
2. Shafts
Show which shaft to use when threading and lifting.
3. Liftings
This is the order the shafts will be lifted for each weft pick. For this
project the first shafts lifted are 1, 3, 5 and 7 by pushing levers 1, 3, 5
and 7 down. Note - lever 1 is on the left and lifts shaft 1, the front shaft.
4. Drawdown
The diagram of the woven cloth produced by the threading and shaft
liftings.
pcw6
1. Threading Draft
8
7
7
6
6
5
5
5
4
4
4
3
3
3
2
2
2
2
1
1
4. Drawdown
x8
8
8
7
7
7
7
6
6
6
6
5
5
5
4
4
4
3
3
2
2
1
Ashford Handicrafts Limited
415 West Street, Ashburton 7700, New Zealand
Telephone 64 3 308 9087
[email protected] www.ashford.co.nz
Winding the Warp for the Table Runner
Warp Colour Order
Using a warping frame wind on the warping threads in the following
sequence:
Remember: Each trip from the start peg to the end peg and back again
will be two warp ends.
1. Wind 20 ends Black
2. Wind 20 ends Grey
3. Wind 60 ends White
4. Wind 40 ends Grey
5. Wind 60 ends White
6. Wind 20 ends Grey
7. Wind 20 ends Black
Start peg
End peg
* The raddle cross will be made after each group of 10 threads.
Continue as per instructions in the Learn to Weave on the Table
Loom booklet with the following exception.
Step 11. Release one end of the cross stick. Slide each group of
threads off the cross stick and onto the raddle. To ensure warp
is centred place first group of threads in the
centre pin of the raddle.
page 1
8
7
6
5
2. Shafts
4
3
3
2
2
1 2 3 4 5 6 7 8
1
1
3
5
7
2
4
6
8
1
3
5
7
2
4
6
8
1 2
4 5 6
2 3
5 6 7
3 4
6 7 8
1
4 5
7 8
1 2
5 6
8
2 3
6 7
1
3 4
7 8
1 2
4 5
8
2 3
5 6
3 4
6 7
1
4 5
7 8
1 2
5 6
8
1 2 3
6 7
2 3 4
7 8
1
3 4 5
8
3. Liftings
Threading
cross
Raddle
cross *
15th
space from the
KTL120418V3