Ashland PS50 작동, 성능 및 사양 매뉴얼 - 페이지 2

{카테고리_이름} Ashland PS50에 대한 작동, 성능 및 사양 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Ashland PS50 18 페이지. Anodized aluminum sump pump

페이지 인쇄

Before installation, read the following instructions care-

fully. Failure to follow instruction and safety information

could cause serious bodily injury, death and/or property

damage. Each Ashland Pump is individually factory tested

to ensure proper performance. Closely following these

instructions will eliminate potential operating problems

assuring years of trouble-free service.

Most accidents can be avoided by using common sense.

IMPORTANT - Ashland Pump is not responsible for

losses, injury or death resulting from failure to observe

these safety precautions, misuse, abuse or misapplica-

tion of pumps or equipment.

All returned products must

DANGER

be cleaned, sanitized, or

decontaminated prior to shipment, to

ensure employees will not be exposed to

health hazards in handling said materials.

All applicable laws and regulations shall apply.

Bronze/brass fitted pumps may

WARNING

contain lead levels higher than con-

sidered safe for potable water systems. Government

agencies have determined that leaded copper alloys

should not be used in potable water applications.

Installation, wiring, and junction

WARNING

connections must be in accord-

ance with the National Electric Code and all applicable

state and local codes. Requirements may vary depend-

ing on usage and location.

Installation and servicing is to be

WARNING

conducted by qualified personnel only.

Rotating machinery. Amputation

DANGER

or severe lacerations can

result. Keep clear of suction and

discharge openings. DO NOT insert fingers

into pump with power connected.

Always wear eye protection when

WARNING

working on pumps. Do not wear loose

clothing that may become entangled in moving parts.

Pumps build up heat and

DANGER

pressure during operation.

Allow time for pumps to cool before handling or ser-

vicing.

Hazardous Voltage can shock,

DANGER

burn or cause death. This pump is

not intended for use in swimming pools or

water installations where human contact with

pumped fluid is possible.

Risk of electrical shock. To

DANGER

reduce risk of electrical shock,

always disconnect pump from power source

before handling. Lock out power & tag.

Sump Pumps

Model: PS Series

Specifications

WARNING

factures recommended maximum performance, as this

could cause the motor to overheat.

WARNING

illness or disease. Wear adequate protective clothing

when working on a used pump or piping. Never enter

a basin after it has been used.

WARNING

waste disposal unit or toilet: Seafood Shells, Aquarium

Gravel, Cat Litter, Plastic Objects, Sanitary Napkins or

Tampons, Diapers, Rags, Disposable Wipes or Cloth,

Medications, Flammable Material, Oil or Grease,

Strong Chemicals, Gasoline.

•

OVERLOAD PROTECTION

This pump series has a built in thermal protection switch,

it will protect motor from burning out due to overheating/

overloading. When motor cools down, overload protector

will automatically reset and start motor.

If overload trips frequently, check for cause. It could be a

stuck impeller, wrong/low voltage or electrical failure in

motor. If an electrical failure in the motor is suspected,

have it serviced by a competent repairman.

Do Not use these pumps in water

over 145°F. Do not exceed manu-

Make sure lifting handles are securely

CAUTION

fastened each time before lifting.

Do not lift, carry or hang pump by

DANGER

the electrical cables. Damage to

the electrical cables can cause shock, burns or

death. Never handle connected power cords

with wet hands. Use appropriate lifting device.

Sump and sewage pumps often

handle materials which could cause

Failure to permanently ground the

DANGER

pump, motor and controls before

connecting to power can cause shock, burns

or death.

These pumps are NOT to be

DANGER

installed in locations classified

as hazardous in accordance with the

National Electric Code, ANSI/NFPA 70.

Do not introduce into any sewer,

either directly, or through a kitchen

Operation against a closed discharge valve will cause

premature bearing and seal failure on any pump.

Any wiring of pumps should be performed by a

qualified electrician.

Cable should be protected at all times to avoid

punctures, cuts, bruises, and abrasions-inspect

frequently.

Never handle connected power cords with wet hands.

Never let cords or plugs lie in water outside the sump pit.

These pumps are offered in a three phase and single

phase wiring configuration. Voltages will vary

according to the application and can be seen in the

tables in this manual.