Acquisitions HIW-XF03G 설치 및 사용자 지침 - 페이지 4

{카테고리_이름} Acquisitions HIW-XF03G에 대한 설치 및 사용자 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Acquisitions HIW-XF03G 16 페이지.

페이지 인쇄

2.0

APPLIANCE DATA

Gas Group

Inlet Pressure

Max Energy Input

Max Gas Rate

Min Energy Input

Pilot Energy Input

Burner Pressure

Main burner flow restrictor

Oxypilot

Gas Inlet Connection

Ignition

Spark Gap

Please see Data label affixed to appliance for current data.

This appliance is for use only with the gas type, and at the pressure stated on the appliance Data

label.

3.0

INSTALLATION REQUIREMENTS

This appliance may be installed with or without a hearth. If a hearth is fitted, the size and design

may be as desired. If the appliance is to be sited near a disused natural draught flue it is recom-

mended that the old flue should be partially sealed off to prevent draughts, however some ventilation

will be required to prevent condensation. The appliance is designed to be wall mounted. It is possible

to install the appliance onto certain types of combustible materials - see section entitled 'Clearances

to combustible materials'.

In the event that the fire is sited near a disused or unserviceable fireplace served by a natural

draught flue, any existing under grate draught device should be sealed off to prevent loss of heat or

creation of draughts. The passageway into the flue should be partially sealed to prevent excessive

draughts, however some ventilation will be required in the old flue to prevent condensation and

dampness. Advice should be sought from your local building control officer.

ROOM SIZING

3.1

X-Fire 1000 models : The room size should be a minimum of 30m 3 (e.g. 11'6" x 11'6" x 8') to

allow adequate circulation of air and ensure the correct operation of the fire.

X-Fire Widescreen models : The room size should be a minimum of 40m 3 (e.g. 13'4" x 13'4" x 8')

to allow adequate circulation of air and ensure the correct operation of the fire.

This volume may include adjacent spaces but these spaces must not be separated by a door. To cal-

culate a room size in cubic metres (m 3 ) divide the room volume in cubic feet (ft 3 ) by 35.3.

SITE REQUIREMENTS

4.0

This appliance is designed to be wall-hung. Do not recess any part of the appliance into the

wall.

This Appliance may be installed in any room in a home, however there are exceptions, and the appli-

ance may not be used in the following rooms;

· Bedrooms - or areas which are mainly used for sleeping.

· Bathrooms - or areas where large amounts of steam are likely to be generated.

Installation in living rooms is common, however other rooms such as kitchens, dining rooms and hall-

ways are permitted, providing a suitable natural gas supply is available, and rooms sizing and venti-

lation requirements are strictly adhered to (see section 4.1).

The appliance is designed to be versatile, and as such will operate correctly when exposed to normal

gentle draughts experienced within the home. It is not recommended, however that the appliance be

X-Fire 1000 models

G20 Natural Gas CAT I2H

20 mbar

Gross

2.6 kW

Net

2.35 kW

0.25 m3/h

Gross

1.5 kW

Net

1.35 kW

Gross

166 W

Net

150 W

High

13.5 mbar. (+/-0.75 mbar). Hot

13.0 mbar. (+/-0.75 mbar). Cold

Low

4.2 mbar. (+/-0.25 mbar). Hot

3.7mbar (+/-0.25 mbar). Cold

Stereo 1.30mm (1/4" BSP)

SIT/Bray 9082

8mm inlet restrictor elbow

Piezo spark

4.0 mm (± 1.0mm)

X-Fire Widescreen models

G20 Natural Gas CAT I2H

20 mbar

Gross

Net

0.34 m 3 /h

Gross

Net

Gross

Net

17.5 mbar. (+/-0.75 mbar). Hot

17.0 mbar. (+/-0.75 mbar). Cold

5.8 mbar. (+/-0.25 mbar). Hot

5.3 mbar (+/-0.25 mbar). Cold

Stereo 1.45mm (1/4" BSP)

SIT/Bray 9082

8mm inlet restrictor elbow

Piezo spark

4.0 mm (± 1.0mm)

3.5 kW

3.15 kW

2.0 kW

1.8 kW

166 W

150 W