Ashly TRA-2150 사양 - 페이지 2
{카테고리_이름} Ashly TRA-2150에 대한 사양을 온라인으로 검색하거나 PDF를 다운로드하세요. Ashly TRA-2150 2 페이지. Tra-series
Ashly TRA-2150에 대해서도 마찬가지입니다: 기술 노트 및 사양 (2 페이지), 사양 (2 페이지), 운영 매뉴얼 (12 페이지), 운영 매뉴얼 (12 페이지), 운영 매뉴얼 (13 페이지)
페이지 인쇄
TRA SERIES
A
& e
s
rchitect
ngineering
Pecs
TRA-2075
The two-channel power amplifier shall deliver a minimum power of 40 Watts RMS per channel into 8 Ohm loads, 75 Watts RMS per channel into 4 Ohm loads, and 75 Watts RMS into 70V/100V loads with both chan-
nels operating. The power amplifier shall have Euroblock input and output connectors. It shall have balanced analog inputs and a 80Hz high-pass filter. The power amplifier shall have a 26db/36dB input sensitivity
switch and remote standby. The output circuitry shall be Class D, convection cooled with a frequency response of 20kHz ±1.0dB, -3dB @ 80Hz due to HPF. Signal-to-Noise shall be greater than 100dB unweighted. The
front panel shall provide the status of power, standby, protect, signal level and clip. The amplifier shall mount in a standard 19 inch rack using two spaces (3.5" high) and weigh 19.9 pounds.
The power amplifier shall be an Ashly model TRA-2075
TRA-2150
The two-channel power amplifier shall deliver a minimum power of 80 Watts RMS per channel into 8 Ohm loads, 150 Watts RMS per channel into 4 Ohm loads, and 150 Watts per channel into 70V/100V loads with
both channels operating. When switched into bridged-mono mode, the amplifier shall deliver at least 300 Watts RMS into an 8 Ohm load. The power amplifier shall have Euroblock input and output connectors. It
shall have balanced analog inputs and a 80Hz high-pass filter. The power amplifier shall have a 26db/36dB input sensitivity switch and remote standby. The output circuitry shall be Class D, convection cooled with a
frequency response of 20Hz to 20kHz ±1.0dB, -3dB @ 80Hz due to HPF. Signal-to-Noise shall be greater than 103dB unweighted. The front panel shall provide the status of power, standby, protect, signal level and clip.
The amplifier shall mount in a standard 19 inch rack using two spaces (3.5" high) and weigh 19.9 pounds.
The power amplifier shall be an Ashly model TRA-2150
TRA-4075
The four-channel power amplifier shall deliver a minimum power of 40 Watts RMS per channel into 8 Ohm loads, 75 Watts RMS per channel into 4 Ohm loads, and 75 Watts RMS into 70V/100V loads with both
channels operating. When switched into bridged-mono mode, the amplifier shall deliver at least 150 Watts RMS into an 8 Ohm load. The power amplifier shall have Euroblock input and output connectors. It shall
have balanced analog inputs and a 80Hz high-pass filter. The power amplifier shall have a 26db/36dB input sensitivity switch and remote standby. The output circuitry shall be Class D, convection cooled with a
frequency response of 20Hz to 20kHz ±1.0dB, -3dB @ 80Hz due to HPF. Signal-to-Noise shall be greater than 100dB unweighted. The front panel shall provide the status of power, standby, protect, signal level and clip.
The amplifier shall mount in a standard 19 inch rack using two spaces (3.5" high) and weigh 30 pounds.
The power amplifier shall be an Ashly model TRA-4075
TRA-4150
The four-channel power amplifier shall deliver a minimum power of 80 Watts RMS per channel into 8 Ohm loads, 150 Watts RMS per channel into 4 Ohm loads, and 150 Watts per channel into 70V/100V loads with
both channels operating. When switched into bridged-mono mode, the amplifier shall deliver at least 300 Watts RMS into an 8 Ohm load. The power amplifier shall have Euroblock input and output connectors.
It shall have balanced analog inputs and a 80Hz high-pass filter. The power amplifier shall have a 26db/36dB input sensitivity switch and remote standby. The output circuitry shall be Class D, convection cooled with a
frequency response of 20Hz to 20kHz ±1.0dB, -3dB @ 80Hz due to HPF. Signal-to-Noise shall be greater than 103dB unweighted. The front panel shall provide the status of power, standby, protect, signal level and clip.
The amplifier shall mount in a standard 19 inch rack using two spaces (3.5" high) and weigh 30 pounds.
The power amplifier shall be an Ashly model TRA-4150