Ashly MX-406 운영 매뉴얼 - 페이지 10

{카테고리_이름} Ashly MX-406에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Ashly MX-406 12 페이지. Stereo microphone/line mixer
Ashly MX-406에 대해서도 마찬가지입니다: 기술 노트 및 사양 (2 페이지), 운영 매뉴얼 (12 페이지), 운영 매뉴얼 (12 페이지), 운영 매뉴얼 (16 페이지)

페이지 인쇄
Ashly MX-406 운영 매뉴얼
Page - 10
Safety Instructions – 3
Introduction - 4

SPECIFICATION

DISTORTION
MX-406 Mixer – 5
THD at +4 dBu, 20Hz-20KHz
Connectors & Cables – 5
THD at +12dBu, 30Hz-10KHz
IMD (SMPTE) at +12dBu
Physical Description - 6
HUM & NOISE (20Hz-20KHz at max preamp gain)
Equivalent input hum and noise
Installation – 7
Residual output noise, TRS outputs, all levels at minimum
Typical Applications - 8
Aux Out, Aux Master and all Ch. Aux at nom.
MAXIMUM VOLTAGE GAIN (±2dB)
Factory Configs - 8
MASTER
Troubleshooting - 9
Dimensions - 9
AUX SENDS
Specifications - 10
Warranty - 11
FREQUENCY RESPONSE
20Hz-20KHz
EQUALIZATION
Bass
Treble
CROSSTALK
Adjacent inputs, 20Hz-20KHz
VU METERS (Stereo Outputs) 0VU = +4dBu
PEAK INDICATORS
PHANTOM POWER
SHIPPING WEIGHT
POWER REQUIREMENTS
Input Specifications
Input
Mic 1-6
Line 1-6
Sub Inputs
Stereo Line In
Output Specifications
Output
Master Out (L, R)
Mono Out
Aux Out
Stereo Line Out
(L, R)
Mic/Line Input to Master Output
Mic/Line Input to Mono Output, 600 ohm load
Mic Input to Aux Master Output, pre ch. level
Mic Input to Aux Master Output, post ch. level
Stereo Line in to Aux Master Output
Unless otherwise stated, specification conditions are: 150 source, Input Level set at "-40", all other controls set at nominal.
Balanced/
Input Level & Pad
Unbalanced
Input level @ -60 (pad out)
Balanced
Input level @ -20 (pad out)
Input level @ -20 (pad in)
Input level @ -60 (pad out)
Balanced
Input level @ -20 (pad in)
Unbalanced
NA
Unbalanced
NA
Balanced/
Source
Unbalanced
Impedance
200
Servo Balanced
600
Transformer Balanced
200
Servo Balanced
680
Unbalanced
Notes: 1. 0 dBu = 0.775 Vrms 2. Sensitivity is input signal level which will produce +4 dBu out with all levels maximum
Copyright© 2007 – Ashly Audio Inc.
Operator Manual – MX-406 Mixer
Peak Clip indicator on each input channel and left and right outputs,
+48 VDC applied to all Mic Inputs, switchable on front panel.
Gradual power-up and down to eliminate "pops".
Load
For use w/
Impedance
Nominal
50 to
1K
600 mics
10K
600 lines
10K
600 lines
10K
600 lines
For use w/
Output Level
Nominal
Nominal
600
lines
+4 dBu
600
lines
+4 dBu
600
lines
+4 dBu
10 K lines
-6 dBu
MX-406
<0.05%
<0.05%
<0.05%
<-127dBu
<-100dBu
<-80dBu
+84dB
+84dB
84dB
99dB
32dB
+0.5/-1.0dB
±12dB at 70Hz, shelving
±12dB at 8KHz, shelving
<-65dB
-21 to +6 VU
illuminates 3dB below clipping
Maximum total current draw = 80mA.
Maximum single channel current draw = 14mA.
100-240 Volts, 50-60 Hz – 30 watts
Max Input
Sensitivity
Connector
before Clip
-80 dBu
-29 dBu
Female XLR
-40 dBu
+10 dBu
1/4"TRS
-20 dBu
+29 dBu
Combo Jack
Female XLR
-52 dBu
-2 dBu
1/4"TRS
+8 dBu
+30 dBu
Combo Jack
-12 dBu
+23 dBu
1/4" TRS
-24 dBu
+23 dBu
RCA
Output Level Max
Connector
before Clip
+23 dBu
1/4" TRS
+23 dBu
Female XLR
+23 dBu
1/4" TRS
+12 dBu
RCA
15 lbs.