Ashly MX-406 운영 매뉴얼 - 페이지 9

{카테고리_이름} Ashly MX-406에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Ashly MX-406 12 페이지. Stereo microphone/line mixer
Ashly MX-406에 대해서도 마찬가지입니다: 운영 매뉴얼 (12 페이지), 기술 노트 및 사양 (2 페이지), 운영 매뉴얼 (12 페이지), 운영 매뉴얼 (16 페이지)

페이지 인쇄
Ashly MX-406 운영 매뉴얼

7.2 Meeting Room, Board Room, or Church Mixer Using Remote Control:

In this illustration, the MX-406 is interfaced with an Ashly VCM-88 eight channel remote level controller,
allowing the mixer to be operated from a distance by a non-technical person. Remote control of the VCM-88 is achieved
through the use of Ashly's RD-8 desk-top remote controller, RW-8 wall-plate version, or PC control using Protea System
Software. The RD-8 and RW-8 use a single mic cable for control data, while PC control uses RS-232 serial communica-
tions. Remote control can be located up to 1,300 feet from the main audio equipment rack.
RD-8 Remote Controller
With 3-Pin XLR Data Cable
3
XL R Dat a Co nne ct o r
1
2
On To p or Back .
D o Not U s e
Trans form e rs.
R em ot e
On
On
Data
D is ab led
V +
Ch. 1
Ch. 2
Ch. 3
Ch. 4
Ch. 5
Ch. 6
Ch. 7
Ch.8
Master
+10
+10
+5
+5
RD-8
0
0
Remote Level Control
- 5
- 5
-10
- 10
-15
- 15
-20
- 20
-30
- 30
-50
- 50
-70
- 70
∞
-
∞
-
Gain (dB)
Gain (dB)
Speaker
Zone 1
(L)
EQ,
Limiter,
Crossover,
Amplifier,
(R)
etc.
Speaker
Zone 2
Typical Application of MX-406 with VCM-88/RD-8 Remote Control

8. TROUBLESHOOTING TIPS

8.1 No Sound

Check the AC power. Is the power switch on? Check the level meters. If they are operating, the problem is
between the mixer and the later components in the system. If there is no meter activity, check to see that you really have
an input signal and that it is on the desired channel.

8.2 Distorted Sound

Something is being overdriven in the signal path. If the clip indicators are active, reduce the channel gain and/
or press in the pad switch on the rear panel. There are many gain adjustments in the mixer itself and probably several
others in other system components which makes it possible to overdrive an input section and then incorrectly try to
reduce the gain of the output section. The best way to approach setting gains is to establish the operating level of input
Operating Manual - MX-406 Stereo Microphone/Line Mixer
Model MX-406
Made In USA
Mono
Output
Stereo
(Transform er
S ter eo
Li ne O ut
Outputs
Balanced)
Aux
Master
+4 8V
Left
Output
Ph ant om
CAUTION
Pow e r
RIS K OF EL E CT RIC SHOCK
DO NO T O P E N
Right
10 0-120 VAC
50 -60Hz 15W
(L)
(R)
Re mo te Co nt ro l
D a ta I nput
OU TPU TS M ay Be W i r ed B alan ce d or U n bala nce d .
** TRS Ins e rtio n I s A va ila bl e - S e e Ow ne r's Ma nua l **
3
A s hly Au dio Inc .
2
1
Ch. 8
A VIS:
M ode l VC X -8 0
RIS QU E D E
CH OC E LE C TR IQU E .
M ade I n US A
N E P AS OU VRIR.
V+
D ata
10 0 - 12 0V AC
50 - 60 Hz 15 W
In
**
Out
(L)
(R)
Ch.6
Ch. 5
Ch.4
Ch. 3
Ch. 2
- 20 dB P ad
-20 dB P ad
-20 dB P ad
-20 dB P ad
-20 dB P ad
( Mic O n ly)
( Mi c On ly )
( Mic O n ly)
( Mi c On ly )
( Mi c On ly )
Mic/Line Input
Mic/Line Input
Mic/Line Input
Mic/Line Input
Mic/Line Input
S ter eo
A u x
Inp ut
-L-
Ch. 6 In ser t
Ch. 5 In sert
Ch. 4 In ser t
Ch. 3 In sert
Ch. 2 In sert
Tip =Ou t Rin g=I n
Ti p =Ou t Ri n g=In
Tip =Ou t R in g=In
Tip =Ou t Rin g=I n
Tip =Ou t R in g=In
-R-
M a ste r O utput
D C Co n tro l
10
1 2
1 - Ch .1
IN PU TS ar e Activ e Bala nced ( Tip is +, R i n g is -) .
2 - Ch .2
10 K
CW
1
3 - Ch .3
4 - Ch .4
Pin 1- 9
5 - Ch .5
9
6 - Ch .6
Ch. 7
Ch. 6
Ch. 5
Ch. 4
Ch. 3
7 - Ch .7
C h. 2
In
**
Out
In
* *
Out
**
In
Out
**
In
Out
In
**
Out
In
**
Out
Up To
Six Mic/Line
Inputs
MX-406
Ch.1
-20 dB P ad
Microphone
( Mic On ly)
Mic/Line Input
3
2
1
Mixer
(+)
(-)
(Single Jack
Ch. 1 In ser t
Tip =Ou t Rin g=I n
TRS Inserts Used)
VCM-88
Channels 1-6
Patched Into
8 - Ch. 8
9 - Mas te r
1 0 - Con tro l CCW
1 1 - (A ux G rou nd )
1 2 - Con tro l CW
1 3-1 4 - ( Aux Da ta In)
1 5 - NC
MX-406 Channel
In
**
O ut
Ch. 1
Insert Points
Channels 7-8
Used For Mixer
Output Control
9