Ashly Protea 4.8SP 운영 매뉴얼 - 페이지 4

{카테고리_이름} Ashly Protea 4.8SP에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Ashly Protea 4.8SP 16 페이지. 24 bit system processor

Operating Manual - PROTEA 4.8SP and 3.6SP System Processors

1. INTRODUCTION

Thank you for your purchase of this Ashly Protea 4.8SP or 3.6SP Digital Crossover/System

Processor. The Protea series builds on the tradition of quality and value which has earned Ashly its

place as a market leader in crossovers, equalization, and signal processing.

The 4.8SP has four inputs and eight outputs, while the 3.6SP has three inputs and six outputs.

The front panel interface allows quick access to all control parameters by offering dedicated function

buttons, eliminating the need for hidden sub-menus. For even faster set-ups and stronger visualization

of Input/Output routing, EQ, and Filter curves, a USB port is provided for use with Windows™ Protea

NE Software. Full control by third party controllers is also available via RS-232.

FCC COMPLIANCE:

This device complies with part 15 of the FCC Rules for class A operation, and is subject to the following two conditions:

1. This device may not cause harmful interference

2. This device must accept any interference received, including interference that may cause undesired operation.

The Protea 4.8SP and 3.6SP utilize state of the art DSP technologies, beginning with 24 bit, 48kHz delta-sigma

A/D converters with 128x oversampling. Digital processing includes Gain, Parametric EQ, Shelving Filters, Time Delay,

Crossover Functions, Compression, Limiting, and Matrix Routing, all taking place in twin 120MHz Motorola DSP56362

high performance DSP processors. D/A conversion uses 24 bit delta-sigma converters with 128x oversampling. All

inputs and outputs are precision balanced and RF protected using XLR connectors.

Front Panel Interface: A backlit 2 x 20 character LCD displays channel and function settings. Dedicated

buttons provide access to all audio functions and system tools. The display indicates the current preset number, then

subsequently shows the selected input or output and its active control parameters. Five segment LED arrays on each

input and output provide audio level information and mute status.

Protea NE Software: The computer interface uses Ashly PROTEA NE SOFTWARE for Windows, which allows

complete PC control of the unit through a USB jack. Protea NE software is supplied with each unit, or can be down-

loaded at no cost from the Ashly web site. Advantages of using the software include greater preset capacity, and a very

intuitive visual representation of the audio routing and control process.

As a part of our system of quality control, every Ashly product is carefully inspected before leaving the factory

to ensure flawless appearance. After unpacking, please inspect for any physical damage. Save the shipping carton and

all packing materials, as they were carefully designed to minimize the possibility of transportation damage should the

unit again require packing and shipping. In the event that damage has occurred, immediately notify your dealer so that

a written claim to cover the damages can be initiated. The right to any claim against a public carrier can be forfeited if

the carrier is not notified promptly and if the shipping carton and packing materials are not available for inspection by

the carrier. Save all packing materials until the claim has been settled.

Note: The AC power switch is on the back panel. The Protea 4.8SP and 3.6SP use a universal input power

supply which will accept any line voltage in the range of 100VAC to 240VAC, 50-60Hz. A standard IEC-320 grounded

AC inlet is provided on the rear panel to accept the detachable power cord. Never remove the AC earth ground

connection to the unit. In the event of fuse failure, refer the product to a qualified service technician for fuse replace-

ment, replacing only with the same type and rating fuse.