Cypress Semiconductor Perform CY62167E MoBL 매뉴얼 - 페이지 3
{카테고리_이름} Cypress Semiconductor Perform CY62167E MoBL에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Cypress Semiconductor Perform CY62167E MoBL 13 페이지. 16-mbit (1m x 16 / 2m x 8) static ram
페이지 인쇄Maximum Ratings
Exceeding the maximum ratings may shorten the battery life
of the device. User guidelines are not tested.
Storage Temperature ................................ –65°C to + 150°C
Ambient Temperature with
Power Applied............................................ –55°C to + 125°C
Supply Voltage to Ground
Potential ........................................................... –0.5V to 6.0V
DC Voltage Applied to Outputs
[5, 6]
in High-Z State
........................................... –0.5V to 6.0V
Electrical Characteristics
Over the Operating Range
Parameter
Description
V
Output HIGH Voltage
OH
V
Output LOW Voltage
OL
V
Input HIGH Voltage
IH
V
Input LOW Voltage
IL
I
Input Leakage Current
IX
I
Output Leakage Current
OZ
I
V
Operating Supply
CC
CC
Current
[9]
Automatic CE Power Down
I
SB2
Current—CMOS Inputs
Capacitance
[10]
Parameter
Description
C
Input Capacitance
IN
C
Output Capacitance
OUT
Thermal Resistance
[10]
Parameter
Description
Θ
Thermal Resistance
JA
(junction to ambient)
Θ
Thermal Resistance
JC
(junction to case)
Notes
5. V
(min) = –2.0V for pulse durations less than 20 ns.
IL
6. V
(max) = V
+ 0.75V for pulse durations less than 20 ns.
IH
CC
7. Full Device AC operation is based on a 100 µs ramp time from 0 to V
8. Under DC conditions the device meets a V
9. Only chip enables (CE
and CE
1
2
left floating.
10. Tested initially and after any design or process changes that may affect these parameters.
Document #: 001-15607 Rev. *A
Test Conditions
I
= –1.0 mA
OH
I
= 2.1mA
OL
V
= 4.5V to 5.5V
CC
V
= 4.5V to 5.5V
CC
GND < V
< V
I
CC
GND < V
< V
O
f = f
= 1/t
MAX
RC
f = 1 MHz
CE
> V
– 0.2V or CE
1
CC
V
> V
– 0.2V or V
IN
CC
f = 0, V
= V
CC
CC(max)
T
= 25°C, f = 1 MHz,
A
V
= V
CC
CC(typ)
Still air, soldered on a 3 × 4.5 inch, two-layer printed circuit
board
CC
of 0.8V. However, in dynamic conditions Input LOW Voltage applied to the device must not be higher than 0.7V.
IL
), byte enables (BHE and BLE) and BYTE need to be tied to CMOS levels to meet the I
[5, 6]
DC Input Voltage
........................................–0.5V to 6.0V
Output Current into Outputs (LOW) ............................ 20 mA
Static Discharge Voltage........................................... >2001V
(MIL-STD-883, Method 3015)
Latch Up Current ..................................................... >200 mA
Operating Range
Device
Range
CY62167ELL
Industrial –40°C to +85°C 4.5V to 5.5V
, Output Disabled
CC
V
= V
(max)
CC
CC
I
= 0 mA
OUT
CMOS levels
< 0.2V,
2
< 0.2V,
IN
Test Conditions
Test Conditions
(min) and 200 µs wait time after V
CC
CY62167E MoBL
Ambient
V
Temperature
45 ns
[4]
Min
Typ
Max
2.4
0.4
2.2
V
+ 0.5V
CC
[8]
–0.5
0.7
–1
+1
–1
+1
25
30
2.2
4.0
1.5
12
Max
10
10
TSOP I
60
4.3
stabilization.
/ I
spec. Other inputs can be
SB2
CCDR
Page 3 of 12
®
[7]
CC
Unit
V
V
V
V
µA
µA
mA
mA
µA
Unit
pF
pF
Unit
°C/W
°C/W
[+] Feedback
[+] Feedback
[+] Feedback