AsiaRF MT7915DAN 매뉴얼 - 페이지 12

{카테고리_이름} AsiaRF MT7915DAN에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AsiaRF MT7915DAN 15 페이지. Wifi6 2t2r dual bands dual concurrents mpcie card ieee802.11ax/ac/a/b/g/n

페이지 인쇄

This module is intended for OEM integrators under the following conditions:

1. Ensure that the end-user has no manual instructions to remove or install module.

2. This module is certified pursuant to Part 15 rules section 15.247, 15.407 and RSS-247.

3. The antenna listed below must include 0.3 dB cable loss compensation.

Frequency Band

2400-2483.5MHz;

5150-5850MHz

2400-2483.5MHz

5150-5850MHz

2400-2483.5MHz; 5150-

5850MHz

4. Label and compliance information

Label of the end product:

FCC:

The host product must be labeled in a visible area with the following " Contains FCC ID: TKZAW7915-NPD".

The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC

Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

ISED:

This transmitter module is authorized only for use in device where the antenna may be installed such that

cm may be maintained between the antenna and users. The final end product must be labeled in a visible

area with the following: "Contains transmitter module IC: 9968A-AW7915NPD" or "Contains IC: 9968A-

AW7915NPD"

Contient le module d'émission IC: 9968A-AW7915NPD

The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product

packaging or product literature which shall be available with the end product or online.

5. Information on test modes and additional testing requirements

This module has been approved under stand-alone configuration.

OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band.

The separate approval is required for all other operating configurations, including portable configurations

with respect to Part 2.1093/RSS-102 and different antenna configurations.

The information on how to configure test modes for host product evaluation for different operational conditions

for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or

other transmitters in a host can be found at KDB Publication 996369 D04.

OEM integrator is still responsible for testing their end product for any additional compliance requirements

required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop

configurations or co-location with another transmitter), then the FCC/ISED authorization is no longer

considered valid and the FCC/IC No. cannot be used on the final product. In these circumstances, the OEM

integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a

separate FCC/ISED authorization.

6. Additional testing, Part 15 Subpart B and ICES-003 disclaimer

Appropriate measurements (e.g. Part 15 Subpart B compliance) and if applicable additional equipment

authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer.

This module is only FCC/ISED authorized for the specific rule parts 15.247, 15.407/RSS-247 listed on the

grant, and the host product manufacturer is responsible for compliance to any other FCC/ISED rules that

apply to the host product as being Part 15 Subpart B/ICES-003 compliant.

1F, 7, Houde Street, Younghe District, New Taipei City, Taiwan, R.O.C

Model Number

ANT010-DAU

ANT003

A245005N

A2405N

A5005N

A245004

A245002

Antenna Type

PCB

Dipole

www.asiarf.com

TEL: +886-2-29407880

FAX: +886-2-29407800

Gain(dBi)

2.4GHz: 5.2

5GHz: 5.5

2.4GHz: 2.5

5GHz: 2.5

2.4GHz: 4

5GHz: 5.1

2.4GHz: 5.2

5GHz: 5

2.4GHz: 4

5GHz: 5.1

2.4GHz: 2

5GHz: 2