Cyrus AV5 사용자 지침 - 페이지 7

{카테고리_이름} Cyrus AV5에 대한 사용자 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Cyrus AV5 10 페이지.

페이지 인쇄

User Instructions

Setting special modes of operation

LFE (Low Frequency Effects) level adjustment

The level of the LFE special effects channel may be adjusted

independantly from other level settings. The range of adjustment for LFE

level is 0dB to –15dB. The factory setting is 0dB.

LFE level may be changed as follows-

Play some program material which includes LFE information.

Press the MODE key 3( until the display shows 'LFE level' and the

current setting (Fig 4.12).

To change the level of LFE, use the ADJUST keys 3^.

Note:- When a sub-woofer is not selected the LFE channel information

will be routed to any 'large' system speakers to avoid information loss.

Dynamic compression

Two dynamic compression settings are provided to reduce the dynamic

range of the system. When dynamic compression is selected, louder

passages will be reduced in volume slightly whilst quieter passages will

be increased slightly. The degree of this effect is greatest with the 'HIGH'

setting. This feature is useful with speaker systems of reduced capacity

or for late-night listening. Some experimentation is recommended to find

the best setting.

Dynamic Compression selections may be made as follows-

Press the MODE key 3( until the display shows 'Dyn. Compression'

and the current setting (Fig 4.13).

To change the setting between OFF, LOW and HIGH, use the

ADJUST keys 3^.

Note:- Dynamic compression will only be effective when playing Dolby

Digital program material.

OPERATING THE CYRUS AV8

Key to the front panel drawing (Fig.2):

20. Standby key

21. Standby light

22. Remote eye

23. Volume bar-graph

Key to the remote control drawing (Fig.3):

30. Mute

31. Stereo

32. Input select

33. Standby

34. Level adjust

35. Exit set up

Keys marked with this symbol are not activated for the AV8

Remote Control Options

In addition to the remote control supplied with the AV8, many other

programmable system remote controls are compatible with the AV8

remote system. A full table of remote control commands is listed in the

Specifications section of this handbook, including additional command

codes for direct access input selection.

Power Control

The mains power switch 1^ is located on the rear panel. This switch

should normally be left on. If the unit is left unattended for long periods it

should be switched off or the product disconnected from the mains power

supply.

When power is applied, the STANDBY key on the front panel 2) or

remote control 3# is used for power control. The Standby light 2! glows

green when the AV8 is operating and red when in standby mode.

When the AV8 is switched to Standby all control settings are remembered

for next use.

Selecting an input

Inputs may be selected from the front panel INPUT SELECT buttons 2& or

with the remote control INPUT SELECT keys 3@. As a new input is

selected the input name and number are displayed briefly, changing to

show the name and decoding system after a few seconds (Fig. 4.14).

Selecting the correct multi-channel decoding mode

Multi-channel

The AV8 can decode multi-channel surround sound recorded with Dolby

Digital, DTS or Dolby Surround encoding systems. Selection of the

correct surround decoding mode is fully automatic and the current

decoding mode will always be shown on the display.

Dolby Pro Logic II options

Music and Movie modes

The Dolby Pro Logic II decoding system includes selectable sound

responses optimised for both Movie and Music reproduction.

The Movie response will correctly decode all Dolby Surround encoded

movie soundtracks using the enhanced features of the Pro Logic II

decoding system to give stereo surround channel information with a full

frequency bandwidth. To switch between Movie and Music modes, press

the MODE key 3( once and use the ADJUST keys 3^ to change the

setting.

Additional settings for Music mode

The Music response enables multi-channel reproduction of stereo music

program material and is user-configurable in the AV8 for setting listener

options of Centre channel width, Dimension and Panorama. These

options may be accessed by further pressing the MODE key 3( to reach

the second, third and fourth options, the setting may then be changed

with the ADJUST keys 3^.

Cyrus AV8

24. Text area

25. Speaker map

26. Level control

27. Input select

36. Adjust keys

37. Speaker hot-keys

38. Input name set-up

39. Mode set-up

40. Noise set-up