Cyrus CD6s 사용자 지침 - 페이지 5

{카테고리_이름} Cyrus CD6s에 대한 사용자 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Cyrus CD6s 7 페이지. Hi-fi products

페이지 인쇄

User Instructions

Program Memory Storage

The CD8x has two program modes – Program and Exclude. Program sets the

CD8x to play the sequence of tracks you like, Exclude sets the CD8x to skip

the tracks you don't like. To set the CD8x to Program or Exclude a selection

of tracks, follow this sequence-

Load a disc.

Press the MEMORY STORE key on the remote control once to set

Program mode (the display will read 'Enter Tracks') or twice to set

Exclude mode (the display will read 'Skip Tracks').

Enter the sequence of tracks to be stored (or skipped) with the remote

control numeric keypad. A maximum of 30 tracks may be stored in the

program memory. If an error is made in the programming sequence,

pressing the stop key will cancel the last entry.

When all the tracks have been stored, press the MEMORY key again

(the display will now read 'Program Ready'.

Press play to begin playing the tracks in the programmed sequence.

NOTE:

1. 'MEMORY FULL' indication will show on the display when the program

stored exceeds 30 tracks or a stored program time of 100 minutes or

greater.

2. When engaging STOP while a program is stored, an extra press is

needed to clear the memory. Thus:

•

Press STOP once to stop the disc.

•

Press STOP a second time to clear the memory.

•

Press STOP a third time to open the tray.

•

One continuous press will accomplish all operations.

FRONT PANEL DISPLAY

Key to the Front Panel Display drawing:

19. Track Display (Two Digit)

Track number, disc reading and error display.

20. Mode Indicator

Indicates the current operation mode (play, pause etc.)

21. Time Display

When the disc is stopped this indicates the total time.

When the disc is playing, either elapsed time for the current track or time

remaining to the end of the disc 2@ will be shown.

23. Repeat Indicator

This symbol indicates that repeat is set.

24. Memory Display

Indicates when a program is stored in the memory.

25. Text display area

For status messages.

(Refer to Fig.3)

OPERATION WITH THE AVRS7 REMOTE CONTROL

The CD8x is supplied with the Cyrus AVRS7 remote control which will control

Cyrus amplifiers, tuners and surround sound decoders in addition to the

CD8x.

System select keys

The AVRS7 will send commands to most products within the Cyrus range.

Commands may be sent to different system components by selecting the

appropriate system select key on the handset. These keys are marked CD,

TU, AV, AV-S and SETUP. The CD, TU, AV, AV-S keys flash to show which

type of product is under control. Commands to a surround decoder from the

SETUP system will flash the AV key.

•

Pressing CD will send commands to the CD8x. This key will also switch

on the CD8x and select the CD input of a stereo amplifier.

•

Pressing TU will send commands to FM Tuners. This key will also

switch on an FM Tuner and select the TU input of a stereo amplifier.

•

Pressing AV will send commands to a DVD player. This key will also

switch on a DVD player and select the AV input of a stereo amplifier.

A stereo amplifier will respond to the volume, balance, mute and input keys

when any of the above systems are selected.

NOTE - The AV-S and SETUP keys are not used to control a stereo system.

Multi-channel Surround Sound Systems

The AV-S and SETUP keys of the AVRS7 will control a Cyrus surround

decoder. If you own a Cyrus decoder which was not originally supplied with

an AVRS7 remote control, a full copy of the AVRS7 instruction sheet is

available on the Cyrus website www.cyrusaudio.com.

CD8x Additional Remote Control Functions

The following additional functions of the CD8x are available via the AVRS7

remote control -

Direct Access Numeric Keypad

Press any numeric key on the handset. The track number will appear on the

display and the CD8x will scan and play the selected track. If the disc has

more than ten tracks the CD8x will briefly wait for entry of a second digit when

appropriate.

When a program is stored, the keypad will enable access only to tracks

included in the program memory.

Display Control

Press the DISPLAY OFF key on the handset to switch the display of the CD8x

off. Pressing this key again restores the display to its normal mode. Switching

the display off stops the digital traffic required to update it and reduces the

load on the power supply. This improves the overall quality of the sound

without adversely affecting the normal functions of your CD8x.

Phase Control

Absolute phase is determined by the audio system and the recording process.

Changes in absolute phase are subtle and are best established from the

listening position. The absolute phase of the audio signal can be changed

from the remote control using the PHASE INVERT key. The display text area

will show the message 'Phase Normal' or 'Phase Invert'.

The performance of the CD8x is unaffected whether the signal is in normal or

phase inverted mode.

Note: When an external D/A converter is used, absolute phase correction is

not applied to the digital output. Phase correction must then be selected at the

D/A converter.

Time Display Selection

The DISPLAY MODE key features selection of two time display modes.

Mode 1

Elapsed time display 2!. The time display will read the time

elapsed from the beginning of the current track.

Mode 2

Remaining time display 2@ with minus sign. The time display reads

time remaining to the end of the disc.

Full Remote Command Listing

A full listing of the command set available from the AVRS7 is listed in the

table overleaf.

Cyrus CD8x & CD6s