Asko 1895 빠른 시작 매뉴얼 - 페이지 2
{카테고리_이름} Asko 1895에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Asko 1895 2 페이지. User manual use & care guide general fr (french version)
Asko 1895에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (12 페이지), 사용 및 관리 매뉴얼 (12 페이지), 빠른 시작 매뉴얼 (2 페이지), (스페인어) Uso Y Cuidado (12 페이지), (프랑스어) Manuel D'utilisation Et D'entretien (12 페이지)
페이지 인쇄
Q Q Q Q Q UICK ST
UICK ST
UICK ST
UICK ST
UICK STAR
1.
Load the dishwasher. (There's no need to pre-rinse. Simply scrape off large food particles before
you load the dishware.)
2.
After you've pushed the baskets back inside the unit, manually rotate the upper and lower spray arms
to be sure they turn freely.
3.
Make sure there is rinse aid in the dispenser. Add rinse aid, if needed.
4.
Add automatic dishwashing detergent and close the dispenser cover. (See "Amount..." below.)
5.
Close the door securely.
6.
Select the desired wash program and option(s). A red light appears above the selected touchpad(s).
7.
Press Start. The dishwasher will start.
AMOUNT OF DISHWASHING DETERGENT TO USE
AMOUNT OF DISHWASHING DETERGENT TO USE
AMOUNT OF DISHWASHING DETERGENT TO USE
AMOUNT OF DISHWASHING DETERGENT TO USE
AMOUNT OF DISHWASHING DETERGENT TO USE
We recommend that you use only unscented, granular automatic dishwashing detergent. Generally, one tablespoon of detergent is
needed for a normal wash load. More heavily soiled items, however, may need more detergent. Also, the amount of detergent
needed can vary due to differences in water hardness. The harder the water, the more detergent you may need. (See page 5.) In any
case, you should never use more than three tablespoons of detergent.
LED
LED
LED WINDO
LED
LED
WINDO
WINDO
WINDOW DISPLA
WINDO
W DISPLAY Y Y Y Y S S S S S
W DISPLA
W DISPLA
W DISPLA
T T T T T emper
emper
emper
empera a a a a tur
tur
tur
e Settings
e Settings
emper
tur
ture Settings
e Settings
e Settings
The wash programs (except Rinse) have water temperature options, as shown in the table below. The LED displays the
temperature selections in degrees Celsius. The table below gives both the Celsius and Fahrenheit temperatures. Once you select
a temperature, it will remain selected until you change it (except the Light and Quick wash programs, which revert to 130° F). We
recommend that you use the lower temperature settings whenever possible to conserve energy.
Wash Program
Pans, Super & Normal
Light & Quick
Program Time
Program Time
Program Time
Program Time
Program Time
When a program starts, the LED displays the time it took that program to run last time. As the program runs, the LED displays the
remaining time. If the time exceeds an hour, the display alternates between the hour and minutes remaining. The hour is designated
by an h (e.g., 1h).
The program times may not always be the same because of variations in the household hot water temperature. The dishwasher
heats the water to the proper temperature for the program selected, so if the temperature of the water entering your dishwasher is
too low, the dishwasher will run longer because it takes longer to heat the water. Raising your water heater setting could help to
shorten the cycle times. If this doesn't help, call the ASKO Advisory Center.
Delay Time
Delay Time
Delay Time
Delay Time
Delay Time
Each time you press Delay, you add one hour to the delay time, up to 12 hours. The number in the LED window increases by one
each time you press Delay. Continue to press Delay until the number of hours you wish to delay running the machine is displayed.
To cancel delay, press the Delay touchpad until the LED displays zero.
Fault Codes
Fault Codes
Fault Codes
Fault Codes
Fault Codes
The LED window displays three fault codes, as illustrated below.
Indicates a fault in the heater. Call your local
service technician.
Indicates high water level in the machine. Call the
ASKO Advisory Center.
UNDERST
UNDERST
ANDING
ANDING
UNDERST
UNDERST
UNDERSTANDING
ANDING
ANDING THE INDICA
When the dishwasher has finished, all of the indicator lights will come on. The lights will remain on until you open the door. When
you open the door, the indicator light for the wash program you last used will come on. If you used the high temperature options and
the heat dry option, those lights will come on, too.
If all of the lights on the control panel flash in sequence, this means the machine has detected an overfill. (See page 7.) Should this
happen, call the ASKO Advisory Center.
COMMONL
COMMONL
COMMONL
COMMONL
COMMONLY Y Y Y Y ASKED Q
ASKED QUESTIONS
ASKED Q
ASKED Q
ASKED Q
1)
Why does my dishwasher run so long?
2)
How do I know when the dishwasher is done?
3)
Why do all of the lights stay on?
4)
Why are all of the lights flashing?
5)
Why am I getting a white film on my dishes?
6)
Why is there always water left in the bottom of my machine?
AR
AR
T PR
T PR
OCEDURES
OCEDURES
ART PR
AR
T PR
T PROCEDURES
OCEDURES
OCEDURES
55° C (130° F)
45° C (110° F)
THE INDICA
THE INDICAT T T T T OR LIGHTS
THE INDICA
THE INDICA
UESTIONS
UESTIONS
UESTIONS
UESTIONS
Temperature Options
65° C (150° F)
70° C (160° F)
55° C (130° F)
65° C (150° F)
Indicates a thermistor fault (heater control). Call your
local service technician.
This simply means the door isn't closed completely.
OR LIGHTS
OR LIGHTS
OR LIGHTS
OR LIGHTS
WHERE TO FIND THE ANSWERS
WHERE TO FIND THE ANSWERS
WHERE TO FIND THE ANSWERS
WHERE TO FIND THE ANSWERS
WHERE TO FIND THE ANSWERS
1)
See page 9 in the Use and Care Guide .
2)
See "Understanding the Indicator Lights" above.
3)
See "Understanding the Indicator Lights" above.
4)
See "Understanding the Indicator Lights" above.
5)
See pages 5 and 8 in the Use and Care Guide .
See page 9 in the Use and Care Guide .
6)
Refer to this page in
the Use & Care Guide .
3, 4
3
5, 6
4, 5
75° C (170° F)